Sorry I should have clarified: I have to do it every time after restarting Windows. The X52 Pro is plugged in all the time. Is that not a good thing? I also just use the X52 Pro, no additional controllers.

I’m relieved now though, knowing that it’s something everyone has to do.

PM sent

My second dial shows up as being called slider in the BMS Setup

@oakdesign:

With Update 1 you have the possibility to add exponentional curve settings to either joystick axes or cursor XY axis.

Read the changelog for U1 section AXIS SETTINGS

Gesendet von meinem SM-G930F mit Tapatalk

Hello there, Oak.

About this matter, I’m trying to finalize those settings and understand what settings should I use, even to get these new ones in BMS config to match those custom made in the Logitech H.O.T.A.S utility.

What suggestions do you have for me? To leave all unchanged perhaps, I guess?

Thanks in advance for your attention too.

With best regards.

On my Saitek, Logitech X52/X65F used always a mixed setup. Everything that can go Direct X so 32 Buttons 8 Axis per device goes Direct X only if there are additional spare buttons such as on my X65F these are mapped through keaboard mapping

I’ve set up my Pinky switch to be ALT in the logi software.

I’ve had to hash around with default bindings in Falcon but it works for me.
Maybe that’ll help?

@drtbkj:

Bruzzer,
There are a few other possibilities. One is the BMS Alternate Launcher. In my x-65 days, I was never able to get the microstick to work with axis(s) but that was before AL . Secondly,you can set the microstick to banded function via SST. I’m not at home to check, but that’s an option if your desired view functions have key commands. Thirdly, I was able to get my Warthog’s second pov hat to work using Voice Attack. Perhaps it would help with your-56 as well.

With registry reordering I always was able to set my ministick to be used as axis both on my X-52 and X-65. Never had to use AL or set them up as bands.

Is the X56 one device or 2 sperate devices?

Hey Klog, I was in your same boat a few days ago.

These videos proved very useful

Follow these and you will be off to a great start

For training, (if you are not familiar), use the BMS training manual in the docs folder and pair the up with these videos

That’s it, you solved it! Now it’s recognized by BMS. Those damn admin rights again! 😉
Thank you very much!

Z9

In the DGFT mode, press in the cursor enable to toggle BORE/SLAVE.

For the AIM-120, you have to hold it in, if you release it it defaults back to SLAVE. And on top of that, for the AIM-120 you have to also hold the UNCAGE knob down to say “yes I really do want to fire this expensive radar guided missile without a radar track”.

thanks

@janjan:

I noticed that you did not assign the rotary knobs on the throttle.
Can you assign them?

Dan

Hi,

Since rotary knobs are axises it can be programmed within “BMS / Setup/ Controllers / Advanced” page or within “Devicedefaults.txt”

Checked “Devicedefaults.txt” and everything seems in order. (Details below) But if that does not work for you, try programming one knob for “Radar Range Knob” and the other for “Antenna Elevation” inside BMS. By the way, the axis definitions also fails for me sometimes (God knows why… 🙂 ) and I also program it inside BMS when that happens… 🙂

Best regards and happy landings. 🙂

Saitek Pro Flight X-56 Rhino Throttle

GUID = {A2210738-0000-0000-0000-504944564944}
AXIS_THROTTLE2 = Y
AXIS_THROTTLE = X
AXIS_CURSOR_X = RX
AXIS_CURSOR_Y = RY
AXIS_RANGE_KNOB = Z
AXIS_ANT_ELEV = RZ
AXIS_HSI_HEADING = SLIDER0
AXIS_HSI_COURSE = SLIDER1

UPDATE: Re-install of Windows has cured the problem. At last a HOTAS!!!

I use CH pedals and to allow my feet to rest on the pedals, I set the dead zone to 90% in DCS. Not sure how to do that in BMS.

Opening the .key in notepad or similar allows direct editing. Directx binds are appended to bottom of file.

I am sorry to say but the new 4.33 U5 keymap is not working for me.
I cannot even find Air to Air weapons cycle.
What is Air to Air weapon key called in the new keymap?

I think under advanced controller setup, view is the setting for in cockpit view. Just change it to the device you use aka trackIR or whatever

Master Arm on?

seems FFB largely fixed that problem now, when the plane is at speed it seems it generates enough FFB to keep the stick upright just with the FFB. lucky me, cause the extension can not be removed easy 😛

Hi all,
Does anyone have a binding file for the Logitech Dual Action PC Gamepad?

Any help in setting this up would be greatly appreciated. I’m running F4 BMS on a laptop.

Kind regards,
Fearless