Need some help with the cannon and the curser pls
-
Hi guys,
after two years without Falcon, i have installed BMS 4.33U3.
Target software 3.0.16.615 is installed.I testet all options for the gun-trigger, but it fires all bullets until it’s empty or with the pulse-option it fires just a single bullet, so i have to press the trigger again and again.
On my curser i have the problem, one single movement and it runs all over the place, it’s not to stop.
The axis settings are as you can see in the pic.
It works perfec earlier, but now, idon’t know what’s wrong.
Have you guys one or two ideas for me to fix my probs?best regards,
Buhli -
$400 joystick with real cursor axes and it’s mapped to press the keyboard shortcuts. Where do I start?
TARGET GUI is an inferior program to TARGET Script Editor. It should be used instead.
Joystick controller is perfect 1:1 F-16 joystick. It does not need to be programmed by TARGET. Exclude it from the TARGET virtual controller and use it separately.
It is a bad practice to use controller software to press virtual keyboard. Use DirectX buttons instead.The steps I would take:
Open TARGET GUI
Press NEW CONFIGURATION button, named, OK
Select only HOTAS WARHOG THROTTLE checkbox in “INCLUDE IN PROFILE”, NEXT, NEXT
Press VIEW SCRIPT button. It will look like thisinclude "target.tmh" int main() { Configure(&HCougar, MODE_EXCLUDED); Configure(&Joystick, MODE_EXCLUDED); Configure(&T16000, MODE_EXCLUDED); Configure(&T16000L, MODE_EXCLUDED); Configure(&LMFD, MODE_EXCLUDED); Configure(&RMFD, MODE_EXCLUDED); Configure(&TFRPRudder, MODE_EXCLUDED); Configure(&TWCSThrottle, MODE_EXCLUDED); if(Init(&EventHandle)) return 1; SetKBRate(32, 50); SetKBLayout(KB_ENG); MapAxis(&Throttle, SCX, DX_XROT_AXIS, AXIS_NORMAL, MAP_ABSOLUTE); SetSCurve(&Throttle, SCX, 0, 0, 0, 0, 0); MapAxis(&Throttle, SCY, DX_YROT_AXIS, AXIS_NORMAL, MAP_ABSOLUTE); SetSCurve(&Throttle, SCY, 0, 0, 0, 0, 0); MapAxis(&Throttle, THR_RIGHT, DX_Z_AXIS, AXIS_NORMAL, MAP_ABSOLUTE); SetSCurve(&Throttle, THR_RIGHT, 0, 0, 0, 0, 0); MapAxis(&Throttle, THR_LEFT, DX_ZROT_AXIS, AXIS_NORMAL, MAP_ABSOLUTE); SetSCurve(&Throttle, THR_LEFT, 0, 0, 0, 0, 0); MapAxis(&Throttle, THR_FC, 0, AXIS_NORMAL, MAP_ABSOLUTE); SetSCurve(&Throttle, THR_FC, 0, 0, 0, 0, 0); } int EventHandle(int type, alias o, int x) { DefaultMapping(&o, x); } ```Fire, save as, save this *.tmc file for later. Close TARGET GUI program. Open TARGET Script Editor. Open *.tmc file saved from before. Press green play button. Find DeviceSorting.txt in Falcon BMS\User\Config folder and change it to read
{FFFF044F-0000-0000-0000-504944564944} “Thrustmaster Combined”
{0402044F-0000-0000-0000-504944564944} “Joystick - HOTAS Warthog”Run BMS. Enter Setup and set joystick as primary controller in drop down menu. Save current key file as new name like Buhli2.key with save button. Find the stick section of the controls in the list and one-by-one highlight them blue and then press the corresponding button on the joystick. Save the key file under Buhli2 or Buhli3 or Buhli4 as needed so you can use the last version if a change has a problem. Now BMS should be configured correctly for the joystick without any problems with keyboard virtualization. The next part is to configure the throttle which is a combination of writing (or more likely copying one I give you) script (it's easier than GUI really) and binding those script outputs just like you did the joystick.
-
Hey Buhli,
You don’t mention the HOTAS you’re using, but I recommend not using Target for either of those functions. The trigger action can be programmed directly in the keyfile listing on the controller page. Just look for the stick/trigger command in the list, select and just pull the trigger.
The cursor can be assigned in the avionics tab in the advanced controller setup. Works flawless for me.Verstuurd vanaf mijn F5121 met Tapatalk
-
You don’t mention the HOTAS you’re using
Of course you posted in the Warthog forum and that’s not telling me anything.
[emoji15] [emoji15] [emoji15] [emoji15] [emoji12]Verstuurd vanaf mijn F5121 met Tapatalk
-
Thank you very much for the quick reply and advises.
I will test it at the weekend and give you some feedback.Buhli