[4.3.3] Can't make a perfect ramp start!
-
Hi,
just installed 4.3.3…, made some first flights and wanted then to make a ramp start.
But it isn’t working any more correctly!As soon the engine is running I switch on the HUD and at once I can read: Warning, warning, warning…
And to right on this board I can read: ‘Avionics failure’ and ‘IFF’
And this lights won’t go off!Anything else seems to work.
With 4.3.2 I never had a problem with ramp start…What am I doing wrong in 4.3.3? Please help!
TIA
Earlybite -
Hi,
just installed 4.3.3…, made some first flights and wanted then to make a ramp start.
But it isn’t working any more correctly!As soon the engine is running I switch on the HUD and at once I can read: Warning, warning, warning…
And to right on this board I can read: ‘Avionics failure’ and ‘IFF’
And this lights won’t go off!Anything else seems to work.
With 4.3.2 I never had a problem with ramp start…What am I doing wrong in 4.3.3? Please help!
TIA
Earlybitertfm
-
-
We already helped. We wrote the manuals. Read the Dash 1 or the Training Manual. Both will take you step by step through the Ramp Start procedure in 4.33.
-
New fault logic has been implemented in 4.33, which require extra steps in ramp.
-
@all:
OK <ayay>!Thanks and
greeting
Earlybite</ayay> -
This post is deleted! -
Hi,
just installed 4.3.3…, made some first flights and wanted then to make a ramp start.
But it isn’t working any more correctly!As soon the engine is running I switch on the HUD and at once I can read: Warning, warning, warning…
And to right on this board I can read: ‘Avionics failure’ and ‘IFF’
And this lights won’t go off!Anything else seems to work.
With 4.3.2 I never had a problem with ramp start…What am I doing wrong in 4.3.3? Please help!
TIA
EarlybiteI solved it with click the F ACK button a few times, but i don’t know if it’s the right step
-
It’s not…
RTFM -
-
I solved it with click the F ACK button a few times, but i don’t know if it’s the right step
Indeed … it is not.
-
BTw, we will eventually break at tell you the correct answer
But try and figure it out yourself, because there are lots of thing to be relearned (not just this bit)…. (Get it? BIT?.. :))
-
I can only test tomorrow (I’m now on my GNU/Linux OS)…, but I can imagine what you mean.
So, start again…from the beginning. OMG, I’m a noob again -
I’ll give you all a tip.
for normal generic startup only two steps are added.with some equipment onboard, you mihgt need a few more steps, usually calibration of some sort
-
Here is explanation:
https://www.benchmarksims.org/forum/showthread.php?23419-Faults-during-ramp-start
-
What exactly is triggering the IFF caution? Is it the PFL, TEST page?
Is it possible (or even correct idea) to start systems in a specific order to avoid some/all of the warnings and cautions (e.g. starting RWR before MMC)?
-
What exactly is triggering the IFF caution?
That’s the sim complaining there is no IFF…lol.
-
What exactly is triggering the IFF caution? Is it the PFL, TEST page?
Is it possible (or even correct idea) to start systems in a specific order to avoid some/all of the warnings and cautions (e.g. starting RWR before MMC)?
The IFF system is not implemented and with a ramp start there’s no way I know of to turn the IFF on to extinguish that caution light. Just F-ACK a couple times to clear the PFLD and caution lights, then Clear the MFD Test page.
-
Why work in reverse??
Clear the TEST page first… -
What exactly is triggering the IFF caution? Is it the PFL, TEST page?
The IFF caution light, indicates that the IFF system was interrogated on mode 4 and is unable to respond because the mode 4 codes (A and B) are zeroized or not coded, mode 4 is not enabled.
IFF caution light will also illuminate if RF switch is in QUIET or SILENT.
Although there is no IFF in BMS, the fault system dose follow the behavior of the real system as closely as possibleIs it possible (or even correct idea) to start systems in a specific order to avoid some/all of the warnings and cautions (e.g. starting RWR before MMC)?
No