RTT Client Issue
-
I am trying to use RTT instead of native BMS export in local but when i launch RTTclient i have this error message : Configuration not complete.
I have added the set g_bExportRTTTextures 1 in the config file.
Can someone tell me what i am missing ? -
Did you also launch RTTServer?
Are you running both Server and Client on the same PC?
Post your RTTClient.ini file```
inside a CODE box -
1- Yes i did.
2- Yes i run on the same PC3- There is a post on check-six which explain the installation. I’ll try with this guide, if i have already a problem i’ll come back to you. Thanks for your help.
-
So i have found my mistake, some position parameters were missing.
My new problem is that it works for the F16 but not for the M2000-D. We already had this problem with Gurra Pit Tools and MFD Extractor. -
-
It is not a coordinate problem, the MFD only displays flickering lines. The problem was the same with MFD extractor and Gurra Pit Tools.
-
Hi,
I have the exact same problem. I get he message; ‘Configuration not complete’ and RTTClient closes. The server only keeps running.
Here’s my RTTClient.ini:RTT Client v2.4
by Dunc, 2019/01
The IP address and port where the server is running.
Supports both IPv4 and IPv6.
HOST = 127.0.0.1
PORT = 44000If you use the client on a networked PC (not locally), it is
possible not only to receive the RTT images, but also the “normal”
shared memory areas. Just enable the ones that you want to access
remotely, it will be created on the client side for you.
DATA_F4 = 0
DATA_BMS = 0
DATA_OSB = 0
DATA_IVIBE = 0These are the displays that we can render on the client. For configuration,
simply pre- or postfix these strings with “USE_” or “_X”, “_Y”, “_W”, “_H”,
like in the examples below.
HUD
PFL
DED
RWR
MFDLEFT
MFDRIGHT
HMS
The RWR is usually displayed without any grid/cirle lines (so you can use e.g.
your own nice glas etchings). However, if you want some (very basic) RWR grid
to be overlayed on the RWR, set the following to 1:
RWR_GRID = 1
Which RTT displays do you want to show on the client side?
USE_HUD = 0
USE_PFL = 1
USE_DED = 1
USE_RWR = 1
USE_MFDLEFT = 1
USE_MFDRIGHT = 1Each display that you want to see must have at least TWO config
entries: X and Y coordinate (of the upper left corner).
Additionally, you can specify the width and the height of the
display. If you do not specify width and height, the original
size of the RTT will be used (but the “no connection placeholder”
will not show the correct size until the server is actually sending
valid data). Note that the X/Y coordinates originate in the upper
left corner of your MAIN windows screen. So you can have negative
coordinates if you e.g. use a monitor to the left or above the main
screen. Examples:
MFDLEFT_X = 3727
MFDLEFT_Y = 326
MFDLEFT_W = 331
MFDLEFT_H = 331MFDRIGHT_X = 4737
MFDRIGHT_Y = 326
MFDRIGHT_W = 331
MFDRIGHT_H = 331RWR_X = 3892
RWR_Y = 25
RWR_W = 236
RWR_H = 233DED_X = 4662
DED_Y = 12
DED_W = 291
DED_H = 94PFL_X = 4666
PFL_Y = 737
PFL_W = 238
PFL_H = 82Thanks for your help
Judy
-
Hi!
Judy1301, try to add USE_HMS = 0, for me was this the problem.
Br
Borut