BMS 4.36 DEV SERIES - AGM 65L
-
@Stevie said in BMS 4.36 DEV SERIES - AGM 65L:
@Fish44 - a lasr Mav should not have a “boresight” mode…
Thats what I would expect.
-
@Fish44 - I think aas close as one could get to “boresight” would be CAGED…however, that will get he missile looking straight ahead off the pylon, and not coincident with the FPM.
I’m also not positively sure if the missile is allowed to enter track while CAGED if it should happen to pick up some energy…like coming over the top on a pop-up roll in. I’ll have to look into that.
-
“…And laser code cannot be adjusted from the MFD…”
What you mean ? I had no problem to change the AGM-65 laser code in the weapon MFD page in training 14 mission.
Do you refer to something else ?
Best,
Eric. -
@ericfa2a That’s the TGP pod laser code. But the weapon laser code cannot be adjusted. It is a feature of that weapon system and was present (though a little cumbersome) in 4.36.
-
@Fish44 - the weapon laser code should be able to be changed for each individual missile, the TGP, or all at once - based on pilot selection. If this is not the case, then a fix is needed.
-
@Fish44 said in BMS 4.36 DEV SERIES - AGM 65L:
@ericfa2a But the weapon laser code cannot be adjusted.
Have you watched the video that’s post 1 of this thread which outlines how to change the laser code of the missile?
-
Our wing as part of the categorization process we fly the Block 15 until the pilot obtains another higher category and we have done dissimilar tests and doing buddy lasing does not give any indication looking with an AGM65L from a block 15, one cannot even change the code that is looking for the AGM-65L, in BORE mode the cursor does not move to put the code in unlock and change it, but nevertheless without any indication, the friend does buddy lasing all the time and we put our plane in eye distance parameters and the AGM-65L goes out and searches for the target.
-
@Fish44 Sorry Fish, I am not talking of the DED page code.
I am talking about the weapon MFD page as it’s written in the DASH 34 manual page 238.
What do you mean about TGP code ? Isn’t the TGP the only way to put the laser on a target ?
@VIPER-0 you must slew the GPI to the L letter and TMS Up to change it in U, again as in the DASH-34 manual page 238 explains.
-
@ericfa2a said in BMS 4.36 DEV SERIES - AGM 65L:
@Fish44 Sorry Fish, I am not talking of the DED page code.
I am talking about the weapon MFD page as it’s written in the DASH 34 manual page 238.
What do you mean about TGP code ? Isn’t the TGP the only way to put the laser on a target ?
@VIPER-0 you must slew the GPI to the L letter and TMS Up to change it in U, again as in the DASH-34 manual page 238 explains.
In Block 15 with AGM-65L the GPI not move, in any mode.
-
@VIPER-0 OK, Thanks for the clarification. I haven’t in mind the difference between blocks. And I don’t use block-15 for now.
-
@VIPER-0 - I’m also pretty sure you shouldn’t be able to slew the GPI outside of the circle…and definitely not left/right - only to set depression, and then only when in Scan.
-
-
Got another L-Movie here… there he changed the laser code in the WPN page of the Maverick… but I am not able to get the X moving by my cursor? Works fine with radar, HSD and so on. but in WPN pager of the laser Maverick I can not get the cross in any direction
Anyone knows what I am doing wrong here? -
@Kuhprah Hi, you must put the AGM 65L in Bore Mode, (by default in PRE) in the weapon or SMS page to be able to move the GPI.
And some peoples have reported that some F16 blocks can’t slew the GPI even with this step. But for the more common ones, no problem.
Cheers,
Eric.