Excellent excellent work. Looks amazing! Μπράβο Μάνο!
Posts made by danaos75
-
RE: McDD F-15C/D/E New model for BMS
-
RE: Engine fire
@dumba If I remember correctly the is a flag in the config for random failures. 2 out of 4 is hardly random but try changing that to 0 and check it on your next flights. set g_bEnableRandomFailures 0
-
RE: Helios on Android
@Sabre Helios and spacedesk here. I use it with USB too, not just for stability but to also charge the tablet.
-
RE: [Released] EMF v3.2.1 (BMS 4.37 U3)........IT'S STILL ALIVE
@AlehandroGTI try putting theater.map on \Falcon BMS 4.37\Data\Add-On emf\Terrdata\Terrain . And Data-Falcon4Theaters.xml on C:\Program Files (x86)\Tacview\Data\Xml . Record a new acmi and it should work. Always backup the original files.
-
RE: Helios - Falcon BMS MFD bindings
@mel-i just to be sure try this.
- Open Helios control center, start the profile I sent you.
- Now load up BMS and start any training mission that you are on the air
- Alt+tab to Helios CC and push the stop button. The profile will close from whatever screen you have it on. And immediately after that press the start button on the Helios CC and the profile will load up again on whatever screen you have it on.
4 Alt+tab to BMS and try the push buttons again.
Hope it helps.
-
RE: Lost All Theaters After 4.37.3 update
@P-J Emf doesn’t work on 4.37.3. At least not yet.
-
RE: Helios - Falcon BMS MFD bindings
@CriticalMass yes exactly the same behavior.
-
RE: Helios - Falcon BMS MFD bindings
@mel-i I 'll send you my profile with this, I have it on my tablet and its working great.
One note though, for the buttons to work I have to start the profile on Helios Control Center, AFTER I enter 3D. Never took the time to figure out why. All the displays work, but the button callbacks only work If I start the profile while in 3D.
You’ve got pm -
RE: Heading tape position
@Teknflyer Get airborne raise your gear, it should move the heading tape down.
-
RE: HMCS Calibration
@coyotte From -34 pg252 chapter 2.5.2.2 HMCS fine alignment : “The system can buffer small movements, but in principle during fine alignment the position and orientation of the HMCS must be maintained”.
Basically it means when you begin any of the fine alignment modes, keep your head still and proceed with your alignment with the cursors.
What I do is before initializing the alignment I simply look forward like I’m looking through the HUD.I experienced the same problem that you show on your video when I was looking down to press 0 to mode select the fine alignment and then looking up at the screen to align the cursor.
-
DED small delay
It does feel like an improvement not a bug but just in case it isn’t, most of the DED pages show a split second delay on displaying some of the info on them.
Definitively was not there before and it adds some processing time to the DED that IMHO looks great!
By the way the cockpit feels like new. amazing, bravo Dev team!Here’s a short video of it on KTO - Dogfight.
-
RE: Terrain Draw or lod distance in 4.3.7.3 in VR
@Nightflyer I remember having the same effect a while back when I had anisotropic filtering set on Nvidia drivers and had it disabled on BMS config file.
Make sure that AF is set on application control on your GPU drivers and x16 on BMS config file, see if that helps.g_nAnisotropicValue = 0 by default for Max value.
-
RE: Alternative Launcher
@Foxl a screenshot from the error would be most helpful. Or at least what is the error and when it is triggered.
-
RE: KAI KF-21 Boramae
@Radium I love watching your 3d models progress on my monitor instead of my phone’s puny screen. I actually try to refrain from watching the photos until I am home at my pc!
Excellent work!
-
RE: Am I being Thick.
@AllenB1971 try pressing ALT-I (or click the little lever on the throttle in 3D) to move the throttle past Idle Detent, to see if that helps.
-
RE: Brakes not working in 3D
@piston check in the launcher axis tab, if the brakes axis have anything assigned to them and remove it