Thanks a million !!! That did the trick
I now have a very reactive response with your profile.
I indeed live in a 3,14 country (Belgium), but my keyboard is US QWERTY, just like my default language and regional settings set to US English in WIN10.
Your profile is excellent and your service second to none :clap2:
Latest posts made by Judy1301
-
RE: AVCS4 Immersive Voice Control Radios for VoiceAttack
-
RE: AVCS4 Immersive Voice Control Radios for VoiceAttack
Hello SemlerPDX. First let me thank you for your amazing VA BMS profiles. Iāve been using them for ages, with a lot of satisfaction.
Iām back in BMS 4.35 after a few months with DCS, but I have an issue. Iāve installed your latest CORE and BMS profile and the installation went smoothly. The problem is in the time necessary for BMS to react to my vocal commands. Iāve timed it and between the moment I say, for instance, āRequest taxi for departureā and the moment the command is actually sent to BMS, it sometimes take 20-30 seconds. I remember your previous profile with the blue radio menus scrolling almost instantly. Now, it takes the profile 10 seconds to go from one menu page to the next. Please note that I also use the Viacom Pro profile for DCS and that it could be something in the VA settings. I hope you can help me with this because it can be annoying. Imagine the time it takes before I get an answer to my āDeclareā calls
Thanks for your helpJudy
-
RE: Bugs reports POH 0.8.3
Hey guys,
Great theater !!! Excellent job, Iām having a blast.:D
Thank you !!
I have a slight problem, though: MFD Extractor doesnāt display the MFDs. All other instruments are OK.
I know this problem was already present in preceding versions of POH and nobody seems to have found a solution.
Any idea where to look ?
Thanks for your help.Judy
-
RE: AVCS4 Immersive Voice Control Radios for VoiceAttack
This is a masterpiece. Iāve been testing it for 2 days and it keeps surprising me
I still donāt fully master all functionalities and I donāt quite understand all of it, but Iām getting there.
One particular little issue I have are āwildcardsā. The profile works perfectly if I just pronounce the commands exactly as indicated in the Comms menus, but if I try to be creative (e.g. āFalcon 11, Ground, F16 two ships, request taxi for departureā) VA doesnāt recognize the phrase, whereas with āRequest taxi for departureā, no problem.
Beats me, but I suppose the issue is on my end. If anyone has ideasā¦ Thanks a lot.Judy
-
RE: Waichou's Helios profile (based on Weeopops profile, thanks !!)
Very interested, Waichou. I really like your work. Can I please try your 4.34 profile ?
Thx
Judy -
RE: RTT Client Issue
Hi,
I have the exact same problem. I get he message; āConfiguration not completeā and RTTClient closes. The server only keeps running.
Hereās my RTTClient.ini:RTT Client v2.4
by Dunc, 2019/01
The IP address and port where the server is running.
Supports both IPv4 and IPv6.
HOST = 127.0.0.1
PORT = 44000If you use the client on a networked PC (not locally), it is
possible not only to receive the RTT images, but also the ānormalā
shared memory areas. Just enable the ones that you want to access
remotely, it will be created on the client side for you.
DATA_F4 = 0
DATA_BMS = 0
DATA_OSB = 0
DATA_IVIBE = 0These are the displays that we can render on the client. For configuration,
simply pre- or postfix these strings with āUSE_ā or ā_Xā, ā_Yā, ā_Wā, ā_Hā,
like in the examples below.
HUD
PFL
DED
RWR
MFDLEFT
MFDRIGHT
HMS
The RWR is usually displayed without any grid/cirle lines (so you can use e.g.
your own nice glas etchings). However, if you want some (very basic) RWR grid
to be overlayed on the RWR, set the following to 1:
RWR_GRID = 1
Which RTT displays do you want to show on the client side?
USE_HUD = 0
USE_PFL = 1
USE_DED = 1
USE_RWR = 1
USE_MFDLEFT = 1
USE_MFDRIGHT = 1Each display that you want to see must have at least TWO config
entries: X and Y coordinate (of the upper left corner).
Additionally, you can specify the width and the height of the
display. If you do not specify width and height, the original
size of the RTT will be used (but the āno connection placeholderā
will not show the correct size until the server is actually sending
valid data). Note that the X/Y coordinates originate in the upper
left corner of your MAIN windows screen. So you can have negative
coordinates if you e.g. use a monitor to the left or above the main
screen. Examples:
MFDLEFT_X = 3727
MFDLEFT_Y = 326
MFDLEFT_W = 331
MFDLEFT_H = 331MFDRIGHT_X = 4737
MFDRIGHT_Y = 326
MFDRIGHT_W = 331
MFDRIGHT_H = 331RWR_X = 3892
RWR_Y = 25
RWR_W = 236
RWR_H = 233DED_X = 4662
DED_Y = 12
DED_W = 291
DED_H = 94PFL_X = 4666
PFL_Y = 737
PFL_W = 238
PFL_H = 82Thanks for your help
Judy
-
RE: Waichou's Helios profile (based on Weeopops profile, thanks !!)
I have, but I must have missed something. My understanding is that Waichou posted his link on Wetranfer and that itās now expired. I know heās working on a new 4.34 profile to come out soon, but I thought I could already have a look at his present one.
-
RE: Waichou's Helios profile (based on Weeopops profile, thanks !!)
Waichou, very impressive work. Iām back in 4.34 and Iād like to try your profile. Could you please update your link?
Thanks a lotJudy
-
RE: SimShaker for DCS World and Falcon BMS support thread
Hey Andre. I did what you suggested and it worked. I have my Simshaker back
Also got rid of Avast and installed Kaspersky, the best IMHO>
Thanks againJudy