Just in case you were not aware of these:
https://www.benchmarksims.org/forum/showthread.php?27619-Spanish-Translation-of-BMS-Dash-1-4-33-1
https://www.benchmarksims.org/forum/showthread.php?27112-Spanish-Translation-of-BMS-Manual-4-33-1
Great!.
Just in case you were not aware of these:
https://www.benchmarksims.org/forum/showthread.php?27619-Spanish-Translation-of-BMS-Dash-1-4-33-1
https://www.benchmarksims.org/forum/showthread.php?27112-Spanish-Translation-of-BMS-Manual-4-33-1
Great!.
Correct. The UHF radio set is one transceiver (transmit + receive) and one receiver (guard receive).
So if I configure the UHF in both mode and channel 15, im transmitting by channel 15 and receiving channels 15 and GUARD. Is’nt it?
The 4 points listed are really only critical in MP as the AI (apart from Tower) will respond regardless of COMM tuning, however I recommend ‘simulating’ it anyway as good practice. All comms are listed in the manuals. Typically, intraflight (talking within your flight, so 11 talking to 12) would be done on VHF, Victor. You’ll notice presets 1-4 are titled Flight1, Flight2,…., and 5-8 are Package 1, Package 2,… I don’t what fixed rules are exactly but each VFS will have their own SOP also.
In the briefing, it saysto tune to preset 12 Uniform (UHF) for Tanker Comms, but the tanker will respond to you regardless, hence why it’s not critical in single player, only recommended for SOP and practice. The frequencies and COMM settings really come alive when flying MP
Page 74 of BMS-Manual.pdf explains the frequencies relative to the DTC. Page 91 (section 7.6) gives more depth on how it’s implemented and tied in with AI use.
Thanks
Now it works fine. Thanks.
Just one question. What are usually the frequencies set from 1 to 14 (I use 15 for the tower control) but I don’t know what other frequencies are useful.
I think I need:
But the other ones?
Thanks
Thanks. When should I use Com1 (UHF) and when Com2 (VHF)?
Hello,
I don’t sure if my knowledge about radio systems are correct or not. Can you tell me if I’m correct?:
There are two radio system in the aircraft (F-16). The primary one (with VHF, UHF, ILS and TACAN) recorded in the computer and the AUX one (only UHF, TACAN and ILS). I can change from one to another one with a selector in the left panel.
If I choose standard one, I’m using the preselected frequencies in the flight computer. If I chose aux then i’m using the frequencies that I can change in the left panel (TACAN and UHF). Is this true?
The problem that I have is that if I play the landing training mission all its ok and I can comunicate with the control tower with the preselected frecuencies (without move to aux radio) but when I flight another mission (i.e. GPB o LGB) when I come back to my base I cannot communicate with the tower control. I’m tried switching from UHF to aux and moving all the wheels in the audio panel but if a press (t -1 o or another command) I don’t speak and I obviously I don’t have answer so I have to land without request the landing). I don’t know what I’m doing bad.
I have the same problem with ILS or TACAN I don’t know how to use the preselected ones.
Thanks for any help
Alt&F3 Man range dn Alt F4 Man range up. This should allow Tgp zoom to work
Thanks!
It works
Hello,
Im starting with LGB`s. I’m following the training mission 11 in Korean theater. All its OK but I don’t know how to use de zoom to get a bet acurrazy on the target. I can change between narrow and wide but the zoom is always 1.0x. I’ve seen youtube videos where people get 4.0x. I suppose it is a wheel or something in the HOTAS or the stick but I’m using a basic stick (Thrumaster X) amd I dont have a HOTAS. Someone know the callback in the config to map it in the keyboard?
Thanks in advance
Thank you very much you two.
Now it works fine.
Rgds.
Ok, I thinks it is TMS - Up