@drillerman52 Yes, the displays are USB powered and connected to the USB HUB. One thing I need to mention. If you are using an NVIDIA Graphics Card for your main display, the two MFD Displays will not show up in the NVIDIA Control Panel. You have to configure them in the Windows Settings/Display Properties.
Posts made by MailMan
-
RE: Viper MIP w/ MFD Displays
-
RE: Viper MIP w/ MFD Displays
@drillerman52 I got a 3.2 powered USB HUB. It came with a 5V power plug. Powered up both MFD’s and the ICP with no problem. You have to make sure it’s USB 3.0. So make sure you have enough for 5 connections at least. I went with an 8 port.
-
RE: Viper MIP w/ MFD Displays
I got mine a couple weeks ago. The ICP is great with DED above it, and the MFD’s are awesome. Very good quality and easy to set up. Comes with a lot of bench stock so you can improvise your install. If you have bad eyes and struggle seeing the MFD info, these are for you. Very easy to setup with the software.
-
RE: Upgrade to FCC3 for Cougar
It is virtually impossible to get the exact same amount of pressure while manually calibrating your cougar unless you are using a push pull gage, I believe the realistic amount is 20 lbs. Your hand and arm are going to feel the force differently in all directions X/Y. Watch the numbers as you push and pull and note the number where you click the trigger to set it. Go the opposite direction the same amount and that will get as close as you can. Make sure have User Mode, Emulation On, and Manual Calibration selected in both boxes. I always check this each time before use and hit apply. It will reload you calibration just in case windows messed with it.
-
RE: Dark Charts for BMS
WOW! These are awesome. Very nice for people with bad eyes and brightness problems. Thanks for your effort.
-
RE: Where?
@Icarus that’s not the same thing that’s in the video you linked to.
-
RE: Where?
@Icarus I’m talking about the panel, not the throttle. Did you make that?
-
RE: Where?
@MailMan I just looked there and all i see is the mission pack. Can you give the link?
-
RE: BMS2Target: BMS to Thrustmaster HOTAS LED Controller (Viper Mission Pack and Viper Panel)
My question is, can you run Target for the indicator lights and still use the Alt Launcher Keymapping at the same time?
-
RE: Happy 25th Birthday Falcon 4.0! 1998-2023+
@Snake122 I have the same CD, but I got mine at a Circuit City. Sorry, no proof of purchase
-
RE: Replaced Viper TQS'?
I received that same calibration procedure and yes, it worked for me. But, It lost it’s calibration again a couple days ago. I ran the same calibration successfully. I wanted to know if anyone that had theirs replaced have experienced the issue with their new one and had to recalibrate?
-
Replaced Viper TQS'?
I know some of you have RMA’d your Viper TQS’s due to the calibration issue. For those who received their replacement, are they working better, or have you had the same issue? Just asking for informational purposes only.
-
Best NVIDIA Control Panel settings for BMS?
I run a 3080TI and was wondering if anyone could share the best NVIDIA Control Panel settings for BMS?
-
RE: Upgrade to FCC3 for Cougar
@jcook I can’t remember if mine is a two or a three, I have had it so long. Still works good.
-
RE: Upgrade to FCC3 for Cougar
@Stevie Awesome. Glad to see I can find one if mine ever goes bad. I wonder who took up this venture. I see they are starting to produce cockpit parts too. I also wonder if those are Mike Williams panel designs.
-
RE: Upgrade to FCC3 for Cougar
@BVT_9 Where is anyone even getting an FCC2 or 3? Arend passed away several years ago.
-
RE: Thrustmaster TQS LED
@benco Can we still use the Alt Launcher key mapping in conjuction with this? Last time I tried Target, it overroad Alt Launcher.
-
WDP and U3
Is WDP working in U3? Every time I go to load a mission it says No Data Loaded and ain’t nothing there.