"Recalculate" function in F4Browse missing in BMS Editor
-
2D <> 3D “event Synchronization” … although most stuff in BMS is calculated in 2D only.
-
The reason I’m asking is cause in RP5 manual in page 242 in paragraph 5 (the whole page actually is important) says even though they set all to abstract the damage was calculated and done.
Also this is for eyecandy for the user only and not actual damage.
I’m not also 100% sure. U guys that have the code can distinguish this… what we can do is zeroish those values and observe results.Sorry if I’m totally wrong about this, but statistical ringed a bell and by refreshing the info I came up on this… so I hope we don’t talk and waste energy here for eyecandy calculations only…
-
The reason I’m asking is cause in RP5 manual in page 242 in paragraph 5 (the whole page actually is important) says even though they set all to abstract the damage was calculated and done.
Also this is for eyecandy for the user only and not actual damage.
I’m not also 100% sure. U guys that have the code can distinguish this… what we can do is zeroish those values and observe results.Sorry if I’m totally wrong about this, but statistical ringed a bell and by refreshing the info I came up on this… so I hope we don’t talk and waste energy here for eyecandy calculations only…
Ok, read that page , he jumps around with different objects but that is all correct what he’s saying .
What they did was make the rockets and frogs/scud abstract cause those missile, rockets arty have no guidance so they visually fire up into air and looked funny . The damage is 2d for all abstract weapons .
The thing with the stats data it also is not just damage affect but how AI work to . for example if you had 0 for low air, or wheeled , then AI won’t fire for low air ac or wheeled vehicle .
So if you added weapon with these fields with values but didn’t update the VCD, UCD you see the issue ?
Of course it depends on what other weapons were calculated and updated correctly .It can get extremely complicated how all the data interacts , with damage though there is a difference between how it calculated in game in bubble and out of bubble even for abstract weapons .
Out of bubble or in 2d map the added damage once the hitpoints vers damage are calculated any extra damage left over gets applied to next vehicle of the unit .
That kind of thing doesn’t happen in bubble in game . -
What they did was make the rockets and frogs/scud abstract cause those missile, rockets arty have no guidance so they visually fire up into air and looked funny . The damage is 2d for all abstract weapons .
Just a sidenote:
That particular one (FROG) can cause CTDs, if called for for duty (or action) in the campaign. I haven´t looked into it yet why (probably even connected to your post above), but i pin-pointed it down to the FROG (we had CTDs, send crashlog to BMS (forgot who), they said, that it looks like a Ground-Unit causing the error and they were right …and the FROG was the reason - removed >> no CTDs anymore at the same campaign-point.).
-
@A.S:
https://i.chzbgr.com/maxW500/4207219712/h8FE7F463/
Just a sidenote:
That particular one (FROG) can cause CTDs, if called for for duty (or action) in the campaign. I haven´t looked into it yet why (probably even connected to your post above), but i pin-pointed it down to the FROG (we had CTDs, send crashlog to BMS (forgot who), they said, that it looks like a Ground-Unit causing the error and they were right …and the FROG was the reason - removed >> no CTDs anymore at the same campaign-point.).
the problem with them is there range was bigger than there bubble, along with no type of guidance (there should be a new type for these type of weapons artillery ) and you can set them to 3d .
So you got ctd even with them set to abstract ?
Don’t remember running into that but probably something simple . -
Long story short. Campaign was running on the server ( i think it was the BFS theater )… server started crashing, 400+ participating pilots waiting … had to hurry fix it… pin-pointed it to the FROG …kicked it out …all was good. Haven´t had time to experiment with a “frog-dissection” ala high-school at that time :mrgreen:
(Will look later what´s going on)
-
In general, sorry, if offtopic but important: https://www.benchmarksims.org/forum/showthread.php?16553-Iff-you-could-have-one-thing-in-the-next-update-it-would-be&p=279962&viewfull=1#post279962
-
Ouch…
255 features only in one Objective…
So a second one is needed to add more features… hmmm
suggestion (yea I now over too much…):
Could those 255 become groups and every group get 255?
So:
A. Objective
1.Feature group 1 (Also naming that group would be helpful to organize things out. Specially for Airports.)
1.1 Feature 1
.
.
.
1.255 Feature 255
2.Feature group2
2.1 Feature 1
.
.
.
2.255 Feature 255
.
.
.
.
255 Feature group 255
255.1 Feature 1
.
.
.
255.255 Feature 255This would kill Lodeditor compatibility… ??? hmmm
Other way around 3 or more objectives on the same place… but Falcon Editor can’t display 2-3 objectives at the same time to align them.
Still u can export reference from one objective to use it and align the second one but not that efficient. -
Don’t know how they are now but on large AB there used to be multiple objectives to make up all objects of AB . one would be large amount of tree’s , another would be runways and main buildings (hangers etc ) .I kind of remember a few had feature count of in 550-600 range .
I know LE worked in AF if you wanted to sue it and AF had higher objective total feature count than SP4 so that should work , at least feature count .
I am sure many use it that do theater work . I used F4browse but new version with decent objective support , though LE worked good to .There was a bug in F4browse if you edit feature on objectives , it would add feature to last objective wrong , forget details but you would have to manually edit the last objective feature list number .
-
For Arty and all:
Though we are straying from topic, I hope it helps y,all
demer