Weapon Delivery Planner released
-
u have to load the dtc once u get in to the cockpit. The pilot goes with his disk to the aircraft and plugs the disk to its place. then he loads the data.
Hello Arty. thanks for the reply. I am loading the DTC from the UI Button just before I hit ‘Takeoff’ icon and the aircraft is started on Runway so DTC should have already been loaded? Only does not load DTC for Ramp Start? Anyway for example if I use the pre-made ‘Long Travel’ TE which is supposed to start from Choongwon UHF 230.15MHz - except the COM1 is showing as 297.5MHz. If I then load the DTC from the DTE in the 3D cockpit then COM1 shows as 15. (presumably Channel 15?) Perhaps I am missing a step or assuming that WDP transfers Airbase frequency when in fact it does not?
-
Hello Arty. thanks for the reply. I am loading the DTC from the UI Button just before I hit ‘Takeoff’ icon and the aircraft is started on Runway so DTC should have already been loaded? Only does not load DTC for Ramp Start? Anyway for example if I use the pre-made ‘Long Travel’ TE which is supposed to start from Choongwon UHF 230.15MHz - except the COM1 is showing as 297.5MHz. If I then load the DTC from the DTE in the 3D cockpit then COM1 shows as 15. (presumably Channel 15?) Perhaps I am missing a step or assuming that WDP transfers Airbase frequency when in fact it does not?
When you enter 3D BMS will overwrite your DTC. But you have a timer on the left side in the WDP. When your DTC is ready and when you entering 3D start the timer and it will save your DTC every 30seconds.
-
to get the airbase freq just on comms in dtc hit set tower then save. when u get in u will hear the tower.
-
to get the airbase freq just on comms in dtc hit set tower then save. when u get in u will hear the tower.
Hello Arty - got it now - thanks for the advice
-
Hey Falcas great program!
But if I change the wingspan range to 32 from 35 feet in dtc/systems/icp WDP(3.4.7) this doesn’t update my Falcon ini file, as when I enter the 3d world my wingspan range still shows 35 feet. However I altered my bingo setting using WDP and this did change in 3d.
Any idea’s?
Snarbs. -
Hi all,
I need a bullseye for print, can anyone help me ……
(72x72 cm Korea ONC Chart)
http://users.skynet.be/bs999158/F4do…navigation.htm
thank
-
Hi,
Gr Falcas
-
Hey Falcas great program!
But if I change the wingspan range to 32 from 35 feet in dtc/systems/icp WDP(3.4.7) this doesn’t update my Falcon ini file, as when I enter the 3d world my wingspan range still shows 35 feet. However I altered my bingo setting using WDP and this did change in 3d.
Any idea’s?
Snarbs.Check post nr 605
Gr Falcas
-
Hi Falcas,
thank you very much….
-
Hey Falcas, thanks for getting back to me.
I double checked and WDP is loading the correct ini file I use for falcon. I still have the same issue that my wingspan range is default at 35 feet(although I changed it to 32 feet in WDP), wheras I changed my bingo fuel in WDP and falcon recognises this change. I have a friend who has the same issue. Any other idea’s?
Snarbs -
IF you have read the post, you should know that the problem is in BMS and BMS needs to be fixed.
Gr Falcas
-
Hi Falcas,
I have two problems.First is that I open a mission file and there are no DPRK packages. I tried more than once with different missions.SS:
Second problem is the program doesn’t see sa-4 in map page.
Thank you.EDIT: First problem was solved (Settings>Reset side)
-
Hi Falcas,
I have two problems.First is that I open a mission file and there are no DPRK packages. I tried more than once with different missions.SS:
Second problem is the program doesn’t see sa-4 in map page.
Thank you.EDIT: First problem was solved (Settings>Reset side)
Good you have seen how the first part works.
The second part is very siple as well. If the SAM is not spotted, it is not shown on the map.
Gr Falcas
-
How can i spot it?
-
How can i spot it?
The word kind of says it all UNspotted. However is the briefing it will probably say intell reports Sa-4 launchers 10nm west of pyangyong. Then you will have an estimate of where the SA-4 is. Offcourse you can just go out fly over and you can “spot” missile launches.
succes
Slack
-
You can’t… as it is not you that spots the battalion, it is the WDP “intel officer” that know which SAMs are spotted or not.
Plan a flight close by as “recon” to spot a battalion will help.gr Falcas
-
I have a question concerning the font size in version 3.4.7.0. When I print out the data sheets or the Coordination Card, the font is larger and darker than that of another of the pilots that I fly with. When I send him my jpg for him to print, they are different from his and the other way around. He sent me one to compare and sure enough, there was a distinct difference. Anyone have any thoughts on this.
-
Different resolution selection maybe?
-
Hi Falcas, i have three questions about the ATIS report and active runway on the datacard.
Yesterday i had setup WDP for a ITO campaign flight from ramat david. One thing i noticed is that the wind direction, speed, temperature and pressure in the WDP ATIS report were different than what i could find through BMS briefing and weather settings (set to probabilistic btw).
It appeared that the active runway was 08, more matching the wind data of BMS briefing. My question is how does WDP create the ATIS report from probabilistic settings and how acurate is it for me to rely on/determine the active runway? Does WDP auto set the active runway based on its own ATIS analysis?Im keeping in mind that ramat david might have some issues (ILS08 for one).
Thanks for helping me getting more out of WDP! Great tool!
Grtz, uit purmereutel. -
I have a question concerning the font size in version 3.4.7.0. When I print out the data sheets or the Coordination Card, the font is larger and darker than that of another of the pilots that I fly with. When I send him my jpg for him to print, they are different from his and the other way around. He sent me one to compare and sure enough, there was a distinct difference. Anyone have any thoughts on this.
The print function is totally different that the saved JPG, so not wondering that you might find some differences.
You could just print out the jpg as this gives you a lot better control for sizing the datacards on the paper that you use.
I almost removed the print function completelyGr Falcas