Mud's Profile
-
i did new bootloader and it’s working like a charm … it was my problem … mate it’s amazing script really good job … all respect …
it did work for a while i didn’t fly i was trying it again and it’s not working again… i don’t understand what’s going on
-
Hey Ramazoti,
If you’re using TrackIR, can you check if F7 there is set to Precision mode? It could be overruling the F7 key so that BMS does not accept the keypress.
Mud
-
@Mud:
Hey Ramazoti,
If you’re using TrackIR, can you check if F7 there is set to Precision mode? It could be overruling the F7 key so that BMS does not accept the keypress.
Mud
Mud You are like a charm … yes i’m using track IR and i tried it now and it’s Finaaaaaly Working … thanx …
-
Great! I’m glad that’s sorted.
Happy flying dude!
-
This post is deleted! -
I’ve recently come back to BMS after a few months break from it. I loaded Muds profile (use to use it all the time) and set the axis within game. All ok. I go into game and it all works. When i load the game again all the axis are reset or don’t work. As per instructions i set the 2 files in the config folder to read only but i still get this issue. Can anyone help please?
edit: i’m finding the same problem with Voodos profile as well. So it’s not profile specific?
-
Sorry gotta ask. Are you setting the files to “Read Only” after setting up the profile and saving first?
-
Yeah, more or less. Setting them to read only isn’t related to the Target script, but just BMS in itself. So once you’re happy with your BMS settings for your hotas, TrackIR, …, exit BMS and set those 2 files to read only.
Like that you’re sure those settings won’t be lost when you start up BMS before loading the script. -
Hi, yeah i set those files to read only after i have set the axis within BMS etc. It still resets the axis though?
-
Hey Muley,
I’m not certain if you’re asking if it’ll still reset the axis, or if you’re experiencing that behaviour.
In either case: setting “axismapping.dat” and “joystick.cal” to read-only should prevent BMS from resetting them / going back to defaults.
Mud
-
Hi Mud,
I go into BMS and then I setup all the axis. I come out of BMS and I set those two files to Read Only. I then run your profile script in Target. Then I run BMS and find that all my axis have reset to default. I’m going to re install the whole thing again and let it install into the default directory. I’m thinking it might be where I have installed BMS, ie spare internal hard drive.
-
Hey Muley,
What you should do is run the script, then start BMS and set your axis settings and whatnot. Then exit BMS and set them to read-only.
After that BMS shouldn’t reset them when you start it “accidentally” without running the script first. -
Thanks Mud. That sorted it. The sequence of doing those steps is crucial. Made a short video to help a buddy out who was having the same problem. If it helps anyone else out.
Thanks for a great profile always use this when i fly BMS.
-
Glad you got it sorted, Muley! It’s often the most simple of things we miss
-
Hi Mud,
Many thanks for the profile but I seem to have issues getting it to work.
I have loaded the KEY into BMS. I ran the TMC file from the Target GUI but im not sure if it has really worked or not. None of the joystick buttons work and the throttle is not mapped as the indication shows.
I have grabbed a screen shot of the script running and hopefully it will make more sense to you as it makes zero sense to me!!!
Regards
FlyingSpanner -
Hmmm, that’s odd. I do launch my script from the TARGET Script Editor (looks a bit different at least). Perhaps you could give that a go.
-
You must launch the tmc file from the Script Editor and not the GUI application.
-
Hi All,
I have run the script from the script editor and no difference.
The buttons which are marked as DX do not seem to work. In my own mapping when I put it as a key press it seems to be ok and the keypress actions as the mapping (done from the GUI- dont have the programming background to do the script editor).
Do you think its a joystick problem? I have only just bought it but its at the latest firmware and all the buttons seem to press ok. When I have loaded my keypressed to a script in the GUI they seem to work. Hence the confusion on why when I follow the instructions for loading the mapping and it does not go as planned im a bit upset and confused.
Help and advice wanted.
Regards
Flyingspanner -
Hey FlyingSpanner,
The buttons which are marked as DX do not seem to work.
Where don’t they seem to work? In the cockpit, or in Windows, …?
-
Hey Mud,
Turns out it is a compatibility issue with my Saitek Pro Rudder pedals.
Loaded all the stuff onto a laptop and it worked fine. Tried it back on desktop sans pedals and operations ok. (I think) just need to try and work out how to operate the buttons now!
Thanks
Spanner!!!