@Arty Out the window? Just speculating…
Posts made by arkady86
-
RE: Updating some 3d models for ground vehicles
-
RE: T-BE5A Brave Eagle
@Radium God, that would be swell! Sending you some hope and cheers! xD
-
JTAC - Why I love the BMS team...
Oh look, you’re fragging a CAS flight but no JTAC is available…
No worries, just frag an Airmobile with a C-130 dropping a Marine squad in the hot zone a few minutes before your TOS and…
BOOM! JTAC is on station!
I love this sim, thank you BMS team…
-
RE: Graphic improvement question.
@Xeno the AIO cooling was already planned, I’m using one now so no way I’m leaving that out
I’m planning on staying on a single 34" monitor, 2560x1080 (I’m using it right now) and MAYBE one day try a Reverb G2 or equivalent, but that’s a big maybe, I’d rather upgrade my pedals or stick for that money…
-
RE: Graphic improvement question.
@Xeno Just to give everyone a baseline idea, my current rig is an i5-4670K with 16GB’s of 1866mhz DDR3 and an 8GB GTX 1070 and fps are absolutely enjoyable and more than playable, with visible dips only on the busiest phases of Rolling Fire day 1 and similar situations (never getting to unplayable states tho).
The bundled rainy day benchmark runs smoothly at all altitudes…
In fact, let me use this post to compliment all the devs, 4.37 performance is better and a lot smoother than 4.36.3, congrats and thank you very much!
I am planning to replace my current setup with an i7-13700KF, 64GBs of 3200mhz DDR4 and a 3060ti, how would you folks rate it as far as future-proofing at an affordable price?
-
RE: Quick (noob-ish) question regarding the campaign COMM ladder
@Sirrah there’s no built-in method AFAIK nor a dedicated kneeboard page through WDP,
but the community always comes to our rescue!Try EZBoards for a quick and reliable solution https://forum.falcon-bms.com/post/19901
Tip: you can even use EZBoards for pages L1 and R1 and WDP (starting with L2 and R2) for the rest of the kneeboard!
-
RE: JTAC says Unable
@Gunz_ProSkies mmm will check everything, maybe I’m missing one of those steps. Thanks a lot, I’ll update when able!
-
RE: g_nIntuitiveSwitches vs. g_nInvertRotaries
@Razor161 I would like to second this request wholeheartedly!
-
RE: HMCS Fine alignment
@drtbkj in roll, cursor should rotate the crosses, you must line them up with the big one. If your alignment were to be bad, in this case the vertical part of the crosses would be tilted when compared to the big one. It’s looking OK in this screenshot, when I align it and it looks like this in roll I just push MSEL and consider it done.
-
RE: JTAC says Unable
@Micro_440th No worries Sir, thanks for your time and patience. Gotta say it went just as I wasw anticipating TBH… The same thing happened in a couple more TEs I tried to put together and I still can’t find the bottom of it. Weird. Will post more updates should I stumble upon anything new. Thanks again!
EDIT: just for completeness’ sake, when testing the TE I tried both flying the whole mission up to JTAC check-in and just jumping in mid-flight right before the S&D STPT, same result…
-
RE: JTAC says Unable
@Micro_440th I would love to, if I could find the attach button in here
-
RE: JTAC says Unable
@Micro_440th the original TE works no problem
-
RE: JTAC says Unable
@Micro_440th as far as I can tell, if I don’t refuel I arrive on target at the same time the original flight was scheduled to and I contact JTAC around 15 miles out… still unable.