Thanx to all for the reply…
Ive solved…
the mistake I made was that I felt the controls in the setup instead of entering the 3D world ahhahahaha in the 3D world works all.
there was no problem in the .key
In the setup you do not see the secondary buttons when using the shift … you see only the primary buttons
but in 3D world work perfet

Have a nice day and thanx again

Hy Guys im here again,
I would like try use the DX input https://www.benchmarksims.org/forum/content.php?153-DirectX-Shifting-Facility
simply without use TARGET Programming

This is my device sorting:
“Joystick - HOTAS Warthog” (0 to 31)
“Throttle - HOTAS Warthog” (32 to 63)
“Thrustmaster Combined”
“Saitek Pro Flight Rudder Pedals”

Ive put in “Falcon BMS.cfg” the 256 input about the shift layer ( set g_nHotasPinkyShiftMagnitude 256 )
I use the BMS-Full.key (as default i dont touch anything here ) inside that we’ve the two command string about the pinky ive check it
SimHotasPinkyShift 2 -1 -2 0 0x0 -1
SimHotasPinkyShift 258 -1 -2 0 0x0 -1

Witout pinky press i get the correct DX for example
i press weapon relaese and i get the correct BMS DX 1 weapons release
but if press and hold pinky (I should get Reset Trim)… instead I get again the weapon release BMS DX 1

Ive try to add also the shiffed time delay sintx in
Falcon BMS.cfg

set g_nHotasShiftQuickPressTimeLimit 300 (ive try with 300 millisends)

But nothing same as above

I dont understand what i miss… or my error

Thanx
by

@TxMtb:

Manually edit your devicesorting.txt to put Thrustmaster Combined as the first line, then the rudders.
Once it’s set there you should be good. IF it changes again for some reason, edit it back and set it to read only.

Yess… work… the Combined TH stay in 1° position device also if i unplug or replug the rudders… ive try also to restart the PC.

Thanx so much guys

Would try that…

Ok I do a test
this is my devicesorting.txt:

“Saitek Pro Flight Rudder Pedals”
“Joystick - HOTAS Warthog”
“Throttle - HOTAS Warthog”
“Thrustmaster Combined”

Today ive try to unplug the saitek rudder (1° device DX1, 2, 3 ecc)
Ive RUN TARGET profile and the Thrustmaster Combined becomes the 1° device!!!
I dont understand… maybe windows 7 dont work like win10?
And for example… if i plug my logitech whell sterring or an gamepad or other device?
I hope do you understand what i mean!
I cant programming any DX in TARGET if F4 dont recognize the device always to the same mode…
I can use only the keyboard!!!.. but… you know that the DX imput are much much better than the keyboard

Yes ok and Thanx so much Gastone, i ve Win7… but i thjink the same thing (because i like that)
I ve any question about this but now im at work when ive two free minuts today i ask
thanx for the moment

Hi guys… sorry for my english
Ive my profile programmed in TARGET with various DX button (DX1 , 2, 3 ecc)
I RUN the profile with TARGET and if i try to use the device analizer it’s all ok… for example if i press the TG1 the analizer say me DX 1
but when i run F4 go in setup controler using the BMS-Full.key… when i press TG1 i get DX33
Yes i know ive the rudder connected (the first device) but i dont understand why if i use TARGET in RUN the programming DX1 in TG1 and the analizer show me DX1… but in F4 setup recognize it in DX33
mahhh… i dont understand
On the BMS-32-U3 i dont have this problem!!!

Anyone help me
thanx

Error 509

Hei Falcas… THANK YOU SO MUCH!!!
Your WDP i’ts wonderfull and the bestsoftware about falcon that i’ve never seen before!!!

You’re the best!!!
Thank you so much for your hard work
THANK
THANK
THANK