Falcon MFD Software for android tablets
-
I am able to change the MFDs. But the MFDs have no display on them…just the OSB buttons work.
-
Almost there. OSB buttons work. However, the MFDs have no display. Did I miss a step?
you should change falcon bms.cfg file as
set g_bExportRTTTextures 1 // This enables the shared texture memory area for HUD/MFDs/HMS/RWR/DED/PFL. This is independent from BMS external window usage! -
you should change falcon bms.cfg file as
set g_bExportRTTTextures 1 // This enables the shared texture memory area for HUD/MFDs/HMS/RWR/DED/PFL. This is independent from BMS external window usage!Yes, this has already been done. Is there a sequence by which the software should be loaded (i.e, bring sim up first, then app). All of a sudden the app does not recognize sim. I may have to completely shutdown and restart…your thoughts.
-
Yes, this has already been done. Is there a sequence by which the software should be loaded (i.e, bring sim up first, then app). All of a sudden the app does not recognize sim. I may have to completely shutdown and restart…your thoughts.
Dracfalcon,
I have it already set up but here is the process I go through. When I was trying to get it set up if I left the test screens open it wouldn’t work correctly. Maybe try these steps and not do any of the testing buttons.
Open server
Select system XP-Win 7 or 8
Press basalt (start)
Open app
Press Left or Right MFD in the app (should highlight blue in the app and green in the server)
Start BMS and fly
Select Flight Data
All should be working at this point -
Dracfalcon,
I have it already set up but here is the process I go through. When I was trying to get it set up if I left the test screens open it wouldn’t work correctly. Maybe try these steps and not do any of the testing buttons.
Open server
Select system XP-Win 7 or 8
Press basalt (start)
Open app
Press Left or Right MFD in the app (should highlight blue in the app and green in the server)
Start BMS and fly
Select Flight Data
All should be working at this pointIt all works with the exception of MFDs showing the display. The server I downloaded was the “setup version” 32 bit. Should I have installed the other server version? I also followed your steps above…still no joy on the display. OSB buttons do work.
-
It all works with the exception of MFDs showing the display. The server I downloaded was the “setup version” 32 bit. Should I have installed the other server version?
That’s the one I used. I also used the 10 inch set up app. I’m free for a couple minutes if you want some help trouble shooting.
-
That’s the one I used. I also used the 10 inch set up app. I’m free for a couple minutes if you want some help trouble shooting.
Yes, I would like some help. Do you want to meet on TS3? If so, need info.
-
Not sure what TS3 is, Ill pm you my number.
-
-
Dracfalcon
can you checkand
they are should be enable
-
Dracfalcon
can you checkand
they are should be enable
Extractions are enabled but still no display on MFDs.
-
did you try test part on server
it should be send image to your android -
I do not see where you confirm (or were asked to confirm) that extraction is on in configuration/settings hardware/cockpit displays to external windows.
I have no idea if needs to be on for this android app but . . . .
-
did you try test part on server
it should be send image to your androidThe test part is a little confusing. I followed your instructions by hitting 5, 5a, 5b, & 5c. What is suppose to happen? I did both with the app on and off. I do not see anything looking like a transfer at all. Can you make the test steps a little more clearer.
I also have my modem going through my wireless router. Does my modem have to be direct connection to my computer? I did notice 2 different IP addresses in the server window when I did a Alt-Ctrl Tab to go back to the server after launching the sim and pressing the COM 1, COM 2, etc.
-
The test part is a little confusing. I followed your instructions by hitting 5, 5a, 5b, & 5c. What is suppose to happen? I did both with the app on and off. I do not see anything looking like a transfer at all. Can you make the test steps a little more clearer.
I also have my modem going through my wireless router. Does my modem have to be direct connection to my computer? I did notice 2 different IP addresses in the server window when I did a Alt-Ctrl Tab to go back to the server after launching the sim and pressing the COM 1, COM 2, etc.
On my set up the server ip’s are all the same. In the top left of the server it says local IP, that is the same as the address in andriod ip to the right in the test area on the server and also the same ip under server ip on the app in the tablet. So in my set up all three server ips are the same. Hope that helps
-
On my set up the server ip’s are all the same. In the top left of the server it says local IP, that is the same as the address in andriod ip to the right in the test area on the server and also the same ip under server ip on the app in the tablet. So in my set up all three server ips are the same. Hope that helps
Komurcu Ive been helping Dracfalcon, my set ups works but just so you know the servers local IP is my android tablet IP and that what I have also in the app IP. Im wondering if there is a way we can change Dracfalcons server local ip to his app ip as that works for me. Also Im unable to use the testing functions but the app works fine and displays whats in the mfd’s
Komurcu, I need to edit this, my desktop ip is displaying in the MFD server not my tablet. Sorry for the confusion. And I did get the test to work. I have worked with Dracfalcon to try to get his app working and we are having no luck. We double checked the config file and also made sure that that mfd cockpit display extraction is selected. I had him uninstall the server and delete the folder then reinstall. Any other ideas?
-
In “test Bölümü” there is Tablet IP , this is your server ip. For testing you have to change as Tablet IP. You have to find your Tablet IP from your tablet , if you start server and press any button on tablet (ICP , MFDs) you can get see ip of tablet on server.
So take tablet ip and write test part and use IMG Gönder button to test
-
All is working fine, but the MFD image in the tablet is not appearing. the osb buttons owrk, the f
chaff/flare numbers is appearing, but not the mfd images on tablet.what i’m doing wrong?
for the server, there’s an english version of it? what is the latest versions?
-
All is working fine, but the MFD image in the tablet is not appearing. the osb buttons owrk, the f
chaff/flare numbers is appearing, but not the mfd images on tablet.what i’m doing wrong?
for the server, there’s an english version of it? what is the latest versions?
I am having the same problem. What tablet are you using? I am using a Samsung Galaxy 2 Tab 10.1. I have also used it on a KindleFire with the same issue.
-
it’s local brazilian made version. you will not recognize it.
but, we may have missing something, the config is little confusing