Morphine's Profile
-
Hello. Morphine,thank you for your profile. It was a great base for mine I learned a lot.
Here I propose some LED works that are pretty useful.
- Initialize LEDs off and a Low Throttle Light Intensity.
- LED 4 Lights on MIL thrust and LED4+5 Light on Afterburner
- LED 1 Lights ON when shift key is active.
- Control backlight on Throttle with Shift+ Left Engine Operation “IGN Up”
NOTE: I changed Shift to Paddle (S4) when Held, and added TIR Center when pulsed.
Cool stuff and thanks for sharing!
-
I was wondering if someone can help me out with this. I’ve tried everything but I can’t figure it out yet.
What I’m trying to do is assign my Shift Coolie Up as F10 (altimeter increase) and Shift Coolie Down as F9 (altimeter decrease). Shift Coolie Right will be F6 (course increase) and Shift Coolie Left will be F5 (course decrease). When I hold down the Coolie switch, I want the program to keep pulsing (not hold) the corresponding key-press (F9 or F10 or F6 or F5) until I release the Coolie switch. I’ve tried REXEC commands but I guess I’m just not getting it. Any help would be great.
Thanks!
-
Hi Morphine
I used your profile for a long time with my old Win7 system. No problems at all.
Recently I bought a new system with Win8 and my Windows recognizes my Warthog as Gamecontroller (1) instead of (0).
Now the hole Keyfile is wrong and useless.I tried to set the warthog to (0) but with no luck at all.
Maybe I am doing something wrong.Is it possible to adjust the keyfile to match the warthog as gamecontroller (1)?
Or how can I set my warthog as controller (0)?Phil
-
Hi Morphine
I used your profile for a long time with my old Win7 system. No problems at all.
Recently I bought a new system with Win8 and my Windows recognizes my Warthog as Gamecontroller (1) instead of (0).
Now the hole Keyfile is wrong and useless.I tried to set the warthog to (0) but with no luck at all.
Maybe I am doing something wrong.Is it possible to adjust the keyfile to match the warthog as gamecontroller (1)?
Or how can I set my warthog as controller (0)?Phil
Does it mean this profile is not working with Windows 8.1 ? I am installing Falcon 4.32 and I wanted to use this wonderful profil with my clean installation.
Thanks for your answer.
PS : Why are you using Target script instead of classical target software program ? It will be easier for us to modify it instead of using script language.
-
It does work without problems as long as the warthog is recognised in Win8 as game controller (0).
-
It does work without problems as long as the warthog is recognised in Win8 as game controller (0).
Where are you seeing the game controller number ?
-
Hi Morphine
I used your profile for a long time with my old Win7 system. No problems at all.
Recently I bought a new system with Win8 and my Windows recognizes my Warthog as Gamecontroller (1) instead of (0).
Now the hole Keyfile is wrong and useless.I tried to set the warthog to (0) but with no luck at all.
Maybe I am doing something wrong.Is it possible to adjust the keyfile to match the warthog as gamecontroller (1)?
Or how can I set my warthog as controller (0)?What device is in the Controller 0 spot?
I’d try unplugging all other USB game controllers and plugging in the Warthog controller into the USB ports attached to the motherboard. Then run the script and see if Thrustmaster Combined combined now appears as controller 0. If it does, then you can plug in any other game controllers and reboot, run the script and see if it stays at 0.
Assuming you can’t get the Thrustmaster Combined controller to show up as Controller 0, then you are going to have to renumber the assignments in the key file using a text editor. See this post for an explanation on how to do that. https://www.benchmarksims.org/forum/showthread.php?8147-Morphine-s-Profile&p=202779&viewfull=1#post202779
-
Where are you seeing the game controller number ?
In the BMS Setup-Page, Axis Control.
The number in brackets after “Thrustmaster Combined”.
Sorry, I can’t explain it any futher because I am not at my flight pc at the moment.
Have a look in the pictures comming with Morphines profile as well. -
What device is in the Controller 0 spot?
My Saitek Rudder Pedals are set to Controller 0.
Thanks for your advises, l will give them a try later.
-
Thank you very much fot this information Takamba.
-
Where are you seeing the game controller number ?
You can also get additional info about the controllers by running the dxdiag.exe utility.
-
I’d try unplugging all other USB game controllers and plugging in the Warthog controller into the USB ports attached to the motherboard. Then run the script and see if Thrustmaster Combined combined now appears as controller 0. If it does, then you can plug in any other game controllers and reboot, run the script and see if it stays at 0.
That helped.
My Thrustmaster Combined is now set as controller 0.Thanks Morphine
-
Hi,
I installed your profile (.key file) and the Target file through the script editor (load it and run it without compiling it) but I just only have the right MFD working. When I am pressing on buttons of my left MFD, nothing happens. Do you have any idea about resolving this issue ?
Thank you very much.
-
Thanks for your hard work Morphine.
I tried to use the LED functionality for MIL power and AB By placing your script between the lines as directed. It didn’t work for me. I am not the most qualified to be doing this sort of stuff but I figured it was easy enough to cut and paste your script between 2 lines. One of the lines in your script scrolls way off to the right, it didn’t look like the rest. Is that right? Any help would be awesome. -
Hi,
I installed your profile (.key file) and the Target file through the script editor (load it and run it without compiling it) but I just only have the right MFD working. When I am pressing on buttons of my left MFD, nothing happens. Do you have any idea about resolving this issue ?
Thank you very much.
I also have another problem : For example the gun trigger is not working whereas trim button on the joystick is ok. It’s like tthere are some buttons working and some others not.
I followed every step of Morphines’s tutorial.
Thanks for your help.
If it can help, my entries running Dxdiag. On BMS,Warthog is seen as “0” device :
-
Morphine, is there a way for me to put my TeamSpeak talk button on the throttle or joystick?
-
I got a new Warthog yesterday and this has been a bit of a pain to get it working. Still one thing to go is slew control is not working in either game nor in device analyzer. Weird thing is that it was working yesterday when I had wrong device numbering and other buttons were not working correctly. Now that I fixed that virtual mouse is dead. I tried to recalibrate joystick while script was running but it didnt help.
Any suggestions?
-
@Greg:
I got a new Warthog yesterday and this has been a bit of a pain to get it working. Still one thing to go is slew control is not working in either game nor in device analyzer. Weird thing is that it was working yesterday when I had wrong device numbering and other buttons were not working correctly. Now that I fixed that virtual mouse is dead. I tried to recalibrate joystick while script was running but it didnt help.
Any suggestions?
This turned out to be a hardware problem, and after dealer replaced it with a new hotas problem was solved. Weird though that you can have a switch that works 2 hours in an equipment that costs 350€.
-
Yes, unfortunately “quality control” is a difficult challenge for all of the consumer joystick vendors. Glad to hear you got it sorted out.
-
Hi Morphine,
I’ve been checking the functioning of the sript for HWorthog and there are some commands that are not working inside the sim.
Still not sure if they are not working or I have done something wrong because now I’m starting at F16.
One example I have is that the NWS configured for Master Mode button with two more aggregate functions. When I press the button on the ground NWS does not work. This script that you created for TARGET where more than one command on the same button a shortcut key is required. In the case of the NWS link for its operation is needed or not, because I was using it with soil and the shortcut to invoke attempt however it still fails.Tks.