Morphine's Profile
-
Where are you seeing the game controller number ?
In the BMS Setup-Page, Axis Control.
The number in brackets after “Thrustmaster Combined”.
Sorry, I can’t explain it any futher because I am not at my flight pc at the moment.
Have a look in the pictures comming with Morphines profile as well. -
What device is in the Controller 0 spot?
My Saitek Rudder Pedals are set to Controller 0.
Thanks for your advises, l will give them a try later.
-
Thank you very much fot this information Takamba.
-
Where are you seeing the game controller number ?
You can also get additional info about the controllers by running the dxdiag.exe utility.
-
I’d try unplugging all other USB game controllers and plugging in the Warthog controller into the USB ports attached to the motherboard. Then run the script and see if Thrustmaster Combined combined now appears as controller 0. If it does, then you can plug in any other game controllers and reboot, run the script and see if it stays at 0.
That helped.
My Thrustmaster Combined is now set as controller 0.Thanks Morphine
-
Hi,
I installed your profile (.key file) and the Target file through the script editor (load it and run it without compiling it) but I just only have the right MFD working. When I am pressing on buttons of my left MFD, nothing happens. Do you have any idea about resolving this issue ?
Thank you very much.
-
Thanks for your hard work Morphine.
I tried to use the LED functionality for MIL power and AB By placing your script between the lines as directed. It didn’t work for me. I am not the most qualified to be doing this sort of stuff but I figured it was easy enough to cut and paste your script between 2 lines. One of the lines in your script scrolls way off to the right, it didn’t look like the rest. Is that right? Any help would be awesome. -
Hi,
I installed your profile (.key file) and the Target file through the script editor (load it and run it without compiling it) but I just only have the right MFD working. When I am pressing on buttons of my left MFD, nothing happens. Do you have any idea about resolving this issue ?
Thank you very much.
I also have another problem : For example the gun trigger is not working whereas trim button on the joystick is ok. It’s like tthere are some buttons working and some others not.
I followed every step of Morphines’s tutorial.
Thanks for your help.
If it can help, my entries running Dxdiag. On BMS,Warthog is seen as “0” device :
-
Morphine, is there a way for me to put my TeamSpeak talk button on the throttle or joystick?
-
I got a new Warthog yesterday and this has been a bit of a pain to get it working. Still one thing to go is slew control is not working in either game nor in device analyzer. Weird thing is that it was working yesterday when I had wrong device numbering and other buttons were not working correctly. Now that I fixed that virtual mouse is dead. I tried to recalibrate joystick while script was running but it didnt help.
Any suggestions?
-
@Greg:
I got a new Warthog yesterday and this has been a bit of a pain to get it working. Still one thing to go is slew control is not working in either game nor in device analyzer. Weird thing is that it was working yesterday when I had wrong device numbering and other buttons were not working correctly. Now that I fixed that virtual mouse is dead. I tried to recalibrate joystick while script was running but it didnt help.
Any suggestions?
This turned out to be a hardware problem, and after dealer replaced it with a new hotas problem was solved. Weird though that you can have a switch that works 2 hours in an equipment that costs 350€.
-
Yes, unfortunately “quality control” is a difficult challenge for all of the consumer joystick vendors. Glad to hear you got it sorted out.
-
Hi Morphine,
I’ve been checking the functioning of the sript for HWorthog and there are some commands that are not working inside the sim.
Still not sure if they are not working or I have done something wrong because now I’m starting at F16.
One example I have is that the NWS configured for Master Mode button with two more aggregate functions. When I press the button on the ground NWS does not work. This script that you created for TARGET where more than one command on the same button a shortcut key is required. In the case of the NWS link for its operation is needed or not, because I was using it with soil and the shortcut to invoke attempt however it still fails.Tks.
-
Thanks for the profile Morphine! One quick question though: Do I have to start the TARGET Script Editor and open the script to run it, or can I create a desktop shortcut or something to launch both the script and BMS in one go?
-
My problem is fixed……!!!
-
Thanks for the profile Morphine! One quick question though: Do I have to start the TARGET Script Editor and open the script to run it, or can I create a desktop shortcut or something to launch both the script and BMS in one go?
You need to start TARGET and RUN the script everytime before starting BMS or you will lose your axes settings (and of course it will not work).
I don’t think there is a way to automate it with one click like you can in the TARGET GUI although I suppose there might be a way to add a command at the end of the script to launch BMS. I just haven’t tried.
-
-
I’ve just come back to BMS after 2 months of being at uni, and the game has forgotten your entire profile and key mappings as it always does after a long period for some reason. Usually I fix this myself, but something else has happened this time - the NWS button on the stick that you allocated as SHIFT has changed it’s functionality to be Left MFD OSB3 for some reason, I didn’t touch a setting so it’s done it purely of it’s own accord. How to I assign it back to it’s SHIFT function?
-
Hi Morphine,
Can you point me to where your G13 and G15 Profiles are located?
Thanks!
-
Hi Morphine, in order to have more realism is not better to change how the speed brake button work? the release of speed brake it’s better if depend from pressure on button….sorry if i not explained well