F-1CG
-
Well another point. On the left side of plane. I see 2 air plugs.
One under the R of armée de l’air and the second under E od DE.Are you sure they are presents on the plane?
I am sure on the right side you can find the second plug (E of DE). This one brings air on a box under (refresh).My 2 cents.
-
Well another point. On the left side of plane. I see 2 air plugs.
One under the R of armée de l’air and the second under E od DE.Are you sure they are presents on the plane?
I am sure on the right side you can find the second plug (E of DE). This one brings air on a box under (refresh).My 2 cents.
Yeap my mistake… The front ones doesnt exist! The smaller ones do! They are on both sides in the same spot (where i have the small ones E or DE) but not the ones in front of them… As for The Ring you mean in length?
Edit: Those inlets already be gone! Anyway only in 1st lod are vissible. Lower lods cause of optimization they don exist
-
Yes Manos for the ring I mean in length, for me the length is too small / length ‘paddles noze pos’.
Diameter is good.I agree : no front inlet. But on the left side there were no inlets when I worked on M F1.
On the right side only one (smaller on) . This inlet brings air on the box for after burners. -
Yes Manos for the ring I mean in length, for me the length is too small / length ‘paddles noze pos’.
Diameter is good.I agree : no front inlet. But on the left side there were no inlets when I worked on M F1.
On the right side only one (smaller on) . This inlet brings air on the box for after burners.Ok i think i can do that therefore its very small difference! As for the inlets i can confirm in two different walkarounds both CT/CR have them on both sides, now they where in all models? who knows! Here in Greece the CG other models had them other not! 123 for ex has them 107 no… (HAF sn numbers)
-
I leave French air force in 2008. So maybe a modification after.
-
I leave French air force in 2008. So maybe a modification after.
Cannot say for sure!
Στάλθηκε από το SM-G970F μου χρησιμοποιώντας Tapatalk
-
Dedicated Wingtip racks and “small” Tanks added Whats next??? Maybe a cockpit…… runs and hides again
Yeah i havent exported the new lods without the double inlets
-
EQ5 on the works. I decided to do 5 as it have minimum changes from CT so it will be easier to make. Major changes are the bulge on the nose that’s gone and the Vertical Fin changed…
Cheers!
EDIT: To the Gurus out here… Right now where u see the Grid black lines is where the CG is on the original dat… I think the real CG has to be aligned with where the main wheels touch the ground but not sure about it. A little help please? I wanted to ask for the CT/CR as well but always forgot
-
EQ5 on the works. I decided to do 5 as it have minimum changes from CT so it will be easier to make. Major changes are the bulge on the nose that’s gone and the Vertical Fin changed…
https://i.ibb.co/2n409Xp/F1EQ5.jpg
Cheers!
EDIT: To the Gurus out here… Right now where u see the Grid black lines is where the CG is on the original dat… I think the real CG has to be aligned with where the main wheels touch the ground but not sure about it. A little help please? I wanted to ask for the CT/CR as well but always forgot
Superb !!! I love it !!! Maybe color contrast is a bit high ?
-
Superb !!! I love it !!! Maybe color contrast is a bit high ?
hmmm… i cannot see much of a difference… unless you mean the edges between the 2 colors to be softer…
Edit:
With FS colors looks like that:
Colors mentioned are FS30475 (Sand) and FS36134 (grey) therefore most of the photos online (not much) shows that isnt in fact too grey but more brown but i can always count the years and exposure of photos as most of them are old …
-
Notice, also, in the thumbnail pic in your post: the Iraqi Mirages have the bullet-shaped BF RWR farings compared to the squared Shelock RWR antenae farings in the .lod pix…
-
Notice, also, in the thumbnail pic in your post: the Iraqi Mirages have the bullet-shaped BF RWR farings compared to the squared Shelock RWR antenae farings in the .lod pix…
Older version
If you read carefully before i corrected the colors i said “Mirage F1EQ-5 on the works” and also “has less differences than CT i already made” if i did EQ4 yeah ok also i would had to get the mk4 seat not mk10
Cheers -
Couldn’t resist… i was going to make new thread but ok i can add a sneak peak preview here. I did obtained written license from mister Ludovic Marbache of the mirage F1 team in Strike fighters 2 to use/manipulate/edit his beautiful cockpit for Falcon BMS (for now personal use of course and still working on it. Credits to mister Ludovich and “Crusader” in CombatACE forums for their co-operation and giving me their work.
Already edited to a percentance that you hardly see from where it comes from and aiming a more “late” CT/CR cockpit
Also : the Mail from mr Ludovic for the proof of giving me license:
More to come in a new thread if the devs have no problem with that…. if they do i delete the pics and everything and forget i mention it
cheers!
-
Very nice!
Στάλθηκε από το MI 5 μου χρησιμοποιώντας Tapatalk
-
this AWSOME!!! Manos you Rock!!!
-
Thanks for your nice words but the real thanks have to go to mr Ludovic and to mr “Crusader” tha gave me their work more of you can find in CombatACE forums!
-
Just curious about projects like this - do you fellows have some sort of GPL agreement going on here?
For instance, if you improve their model or assets, do you hand the new assets back to them so that they can make their own work better, etc? It would be nice to know that the different communities are helping each other to make everything better for everyone involved.
-
Just curious about projects like this - do you fellows have some sort of GPL agreement going on here?
For instance, if you improve their model or assets, do you hand the new assets back to them so that they can make their own work better, etc? It would be nice to know that the different communities are helping each other to make everything better for everyone involved.
As said for now is for personal use only. If i dont get an ok from the devs and moderators i will not post anything else. I wanted to learn about cockpit building thats why i choose something ready and also i was at the time making the mirage so it was perfect. Theres no agreement actually like that but if they need my help or want something for me to make for them i will gladly! They are not the only people and modelers, here as well people and modelers share works and benefit from works or help from others. Radium,Janhas,Dema and other people as well. We all,i believe, have the same and share the same passion for simulators and 3d modeling and of course we all share it with u guys. And in the end we all are benefitted from it
Cherrs
Στάλθηκε από το SM-G970F μου χρησιμοποιώντας Tapatalk
-
Absolutely gorgeous work Manos. Maybe it is time to quit your day job?
-
2 words : Superb work .