Latest posts made by wedge
-
Strategic Planning Map?
Any plans to update the strategic planning map graphics?
-
RE: Ramp start?
I was able to fully complete the ramp start by manipulating the throttle more like advised then hitting idle detent switch/button on the throttle. I wish this was a little more clear in the manual.
Thanks so much for everyone’s help with this.
-
RE: Ramp start?
Section 1.2 of the TO-BMS1F-16CM-1 will show you the location of the SEC light and air cond panel
Also there is a lot of websites and video out there training and showing engine start. (over 14k in google)
For example this video
it has a lot of errors, but it has the basics and is more that good enough to give you an idea. Maybe you can see what your missing.I want to go by the book/proper protocol. I know I could have made notes from videos, but most all are from 4.32 or leave out a lot of steps just to get you up and running. To me if you are going to go through the trouble of ramp starting dont cut corners and use proper protocol for full immersion - the whole point of a ramp start. How many real world pilots short cut it?
-
RE: Ramp start?
I think you should reed the manuals, a lot of this information is there.
I did. I made these notes from the manual because the in depth manual is hard for me to follow while in sim.
-
RE: Ramp start?
I went through the manual and wrote down step by step what Im supposed to do. Trying to follow it to a “T”:
RAMP START (If night - I perform Step 9 first.)
LEFT CONSOLE
1. EXT LIGHTING panel (back).
a. MASTER light switch – NORM.
b. ANTI COLLSION switch - OFF.
c. POSITION – STEADY.
d. WING/TAIL FUSELAGE – BRT.2. AUX COMM panel (back-above EXT LIGHTING).
a. CNI knob – BACKUP.3. FUEL panel (back – above EXT LIGHTING).
a. MASTER FUEL – MASTER (Guard is down).
b. ENG FEED knob – NORM.4. AUDIO 1 panel (Throttle).
a. COMM1 knob – INC.
b. COMM2 knob – INC.
c. MSL knob – set to 12oclock position.
d. THREAT knob – set to 12oclock positon.5. AUDIO 2 panel (Throttle).
a. INTERCOM knob – set to full CW position.
b. ILS knob – INC.6. UHF panel (Throttle; top) – Backup.
a. Lower left knob – BOTH.
b. Lower right knob – refer to briefing and set to MANUAL, PRESET, or GUARD.- If MANUAL – use the 5 small knobs to set frequency.
RIGHT CONSOLE
7. LIGHTING panel (Stick).
a. PRIMARY INST PNL – set CW as needed.
b. DATA ENTRY DISPLAY – set CW as needed.
c. FLOOD – CONSOLES – set CW as needed.
8. AIR COND panel (Stick). I CANT FIND THIS PANEL.
a. AIR SCOURCE knob – NORM.
LEFT CONSOLE
9. ELEC panel (Throttle; below).
a. MAIN PWR – BATT [SHF ALT W].
b. If night Ramp Start: SPOTLIGHT – ON [SHF S]; go back to step 1.10. TEST panel (rear most left panel). Not mandatory – eye candy.
a. FLCS PWR TEST switch – TEST (hold)
b. Wait for 4 FLCS PWR lights to come on.
c. Release FLCS PWR TEST switch.11. ELEC Panel (Throttle; below).
a. MAIN PWR switch – MAIN PWR.12. Close Canopy.
13. ENG & JET START panel (back – above EXT LIGHTING).
a. JET FUEL switch – START 2.14. Observe the following:
a. JFS RUN light comes on after a few seconds.
b. RPMs increase steadily to 20%.
c. At this point check the SEC caution light is off. WHERE IS THIS LIGHT?15. I click Idle Detent and Move Throttle FWD. I MOVE THE THROTTLE TO THE MIDDLE OF ITs RANGE (50%).
16. Observe the following:
a. Monitor lights and engine gauges.
b. FLCS PMG light (ELEC panel) goes off around 40-45% RPM.
c. JET FUEL switch automatically snaps to OFF around 55% RPM. –-------------------- I GET TO THIS POINT AND THEN THE RPMs DROP TO 0%. NOTHING ELSE HAPPENS.
d. ENGINE light (right eyebrow) turns off around 60% RPM.
e. STBY GEN light (ELEC panel) turns off around 60% RPM.
f. MAIN GEN light (ELEC panel) turns off about 10 sec. later.
g. HYD/OIL PRESS light (right eyebrow) turns off between 15%-70% RPM.
h. Check Fuel Flow (700-1700 PPH).
i. Check Oil Pressure (min 15 PSI).
j. Check Nozzle Position (greater than 94%).
k. Check FTIT (below 650 deg C).
l. Check HYD A&B pressure (at the 12 o’clock position).I try proceeding, but the DED, MFDs do not come or the HUD.
RIGHT CONSOLE
17. AVIONICS POWER panel (stick).
a. MMC switch – ON.
b. ST STA switch – ON.
c. MFD switch – ON.
d. UFC switch – ON.
e. GPS switch – ON.
f. DL switch – ON.
g. Wait for DED to come online.
h. INS knob – ALIGN NORM.18. SNSR PWR panel – (stick).
a. RDR ALT – STBY.
b. LEFT HDPT – ON.
c. RIGHT HDPT – ON.
d. FCR – ON.19. Observe the following:
a. Check INS has started aligning – look at DED for INS being incremented.
b. Check flags on ADI. AUX yellow flag on ADI disappears after 60 sec. into INS alignment.20. Turn HUD on: ICP SYM thumbwheel – UP. AS SOON AS I NOTICE THAT THE HUD WONT COME ON - THIS IS WHERE I STOP WITH THE RAMP START.
21. F-ACK (left eyebrow) – PRESS. Review the PFLD.
22. MASTER CAUTION light – PRESS.
23. MFD TEST page – PRESS OSB 3. Clears (MFL) Maintenance Fault List.
LEFT CONSOLE
24. AUX COMM (back-above EXT LIGHTING).
a. CNI knob – UFC.
FRONT
25. Select DTE page on the MFD. Press OSB 3 (LOAD button).
26. ICP – press COM1.
27. DED - input the frequency with the ICP numeric keys.
28. ICP – press ENTR.
29. ICP – press COM2.
30. DED – input the frequency with the ICP numeric keys.
31. ICP – press ENTR.LEFT CONSOLE
32. TEST panel (Not necessary - Eye candy).
a. FIRE OHEAT DETECT – press, hold, and check:- ENG FIRE warning light is on.
- OVERHEAT caution light is on.
- MASTER CAUTION light is on.
- All lights go off when button is released.
b. MAL & IND LTS – press, hold, and check: - Listen for Voice Message System (VMS).
- Check lights are illuminated.
- If no audible sound is heard check INTERCOM knob.
c. PROBE HEAT switch – UP position. (Check MASTER CAUTION light remains OFF.)
d. PROBE HEAT switch – TEST position. (Check PROBE HEAT flashes on the caution panel.)
e. PROBE HEAT switch – OFF.
33. Test FLCS – move Stick and Rudder.
34. FLT CONTROL panel (Not necessary – Eye candy).
a. FLCS BIT switch – BIT.- Green RUN light comes on – flight controls are tested in sequence.
- FLCS BIT WARN will be displayed in HUD.
- T/O LDG CONFIG light may also flash.
- At the end of the test the switch will revert back to original position.
- RUN light will go out.
- If test fails – FAIL light. Perform BIT test again.
b. DIGITAL BACKUP switch – UP;
- Check right eyebrow for DBU light.
- Move Stick/Rudder and check correct operation.
- Move the DIGITAL BACKUP switch – OFF.
c. Once FLCS tests are complete check all switches are in DOWN position.
35. MANUAL TRIM panel.
a. Check that all needles are centered.
b. TRIM/AP DISC switch – DISC.- Ensure that stick trim actions do not cause flight control movement or needle deviation.
c. TRIM/AP DISC switch – NORM. - Apply stick trim and check needle deviation and re-center.
AIR REFUEL CHECK
36. FUEL panel.
a. AIR REFUEL switch – OPEN.- Check right indexer for a blue RDY light.
- Press the stick DISC button and RDY should be replaced by an amber DISC indication. After 3 seconds the DISC should go out and RDY light should return.
b. AIR REFUEL switch – CLOSE. Blue RDY light should go out.
EPU TEST
37. EPU panel.
a. EPU switch – OFF (left click).
b. EPU switch – NORM (right click).
38. ELEC panel.
a. Check both the EPU GEN and EPU PMG lights are off.39. TEST panel.
a. PRK Break – disengaged. (Make sure aircraft is still on chocks.)
b. Move throttle to 80% RPM.
c. EPU/GEN switch – toggle and hold. Check lights:- EPU AIR light on (EPU panel).
- EPU GEN and EPU PMG lights off (ELEC panel).
- EPU RUN light (EPU panel) comes on after 5 seconds.
- If green EPU RUN light fails to come on reinitiate the test with slightly higher throttle setting.
d. EPU/GEN switch – release. Return throttle to idle.
40. ECM panel.
a. OPR switch – OPR.41. AUDIO panels.
a. Check correct volumes on COMM1, COMM 2, and INTERCOM.
SEC CHECK (steps 42- 43 not mandatory)
42. ENG & JET START panel.
a. ENG CONT switch – SEC.- MASTER CAUTION light and SEC caution light should come on.
- Check NOZ POS indicator (right instrument stack.) Engine nozzle closes and should indicate less than 5%.
- Check smooth RPM operation while in SEC.
b. ENG CONT switch – PRI. Close switch guard. - MASTER CAUTION and SEC lights should go out.
43. SPEED BRAKES.
a. Throttle Speed Brake switch - hold DOWN to open.
b. Check SPEED BRAKE indictor all dots showing (panel above throttle by yellow lever).
c. Throttle Speed Brake switch-UP to close. Hold UP until CLOSE is shown on SB indicator.44. THREAT WARNING AUX panel – left auxiliary console.
a. POWER button – Press. SYSTEM POWER green light should illuminate.45. CMDS panel.
a. RWR switch – ON.
b. JMR switch – ON.
c. 01 switch – ON.
d. 02 switch – ON.
e. CH switch – ON.
f. FL switch – ON.
g. MODE knob – AUTO.46. GEAR panel.
a. CAT I/III Switch – set according to your loadout.47. THREAT WARNING PRIME panel
a. SYS TEST button – Press. Check indication on the RWR displays.
b. MSL LAUNCH indicator – Press.
c. HANDOFF button – Press.
SET MFDs AND UFC
48. ICP 2 A-LOW – Press.
a. Move DCS down to MSL FLOOR.
b. Input 14000 and press ICP ENTR (low alt warning for Korea).49. ICP 1 T-ILS – Press.
a. Input ground TACAN (check frequency & band for the air field – 75X is for Kunsan).- CHAN - Input ICP 7 then ICP 5.
- BAND - If Y band is active, enter ICP 0.
- Make sure TCN is set to T/R mode. If not DCS right to cycle.
- Press ICP ENTR.
b. Input ILS frequency for Runway (Runway 36 for Kunsan is 110.3).
- Move DCS to the active line where the TACAN was entered and input 11030, then ENTR. The system automatically recognizes frequency and inputs it to FRQ.
- Check DED to make sure it displays ILS ON. If OFF go to AUDIO 2 panel and switch to ON.
50. Input BINGO Joker level.
a. ICP LIST – Press.
b. ICP 2- Press.
c. Select BINGO page and input 3000. Press ICP ENTR.
FUEL CHECK
51. FUEL QTY SEL panel.
a. Knob – TEST- Check both needles of the fuel gauge. 2000lbs and 6000 lbs.
- Check both FWD and AFT FUEL LOW lights should be illuminated on the caution panel.
b. Knob-NORM; A/L = 2675-2810 lbs., F/R = 3100-3250 lbs.
c. Knob – RSVR; both needles should read 460-480lbs.
d. Knob – INT WING; both needles should read 525-550 lbs.
e. Knob - EXT WING; both should read 2300-2420 lbs (when carrying 370 gal wing tanks).
f. Knob – EXT CTR; A/L = 0 lbs., F/R = 1800-1890 lbs (when carrying a centreline).
g. Return knob to NORM.
PILOT FAULT LIST DISPLAY (PFLD) CHECK
52. Check the PFLD for any faults not acknowledged.
53. F-ACK – Press.
54. Check MASTER CAUTION light.
55. Check EPU fuel quantity – should be 95-102%.
INS ALIGNMENT CHECK
56. HUD - Check if ALIGN is flashing.
a. If ALIGN is flashing go to AVIONICS POWER panel.
b. Toggle the INS knob from ALIGN NORM to NAV.
57. GEAR panel
a. LANDING LIGHT – TAXI.
b. PARKING BRAKE – ON.
58. EXT LIGHTING panel.
a. ANTI COLLISION lights – ON.
b. POSITION .- FLASH.
- WING/TAIL-BRT.
- FUSELAGE-BRT.
59. Arm Seat.
60. Stick - Enable NWS.
ATC
61. TOWER COMMANDS – Tower Page. 8 Remove Chocks.
62. TOWER COMMANDS – Approach Page. 1 Request QNH (write down local pressure setting).
63. Input QNH into Pressure Window of the Altimeter.
64. TOWER COMMANDS – Approach Page. 6 Takeoff Runway.
65. TOWER COMMANDS – Tower Page. 5 Request Taxi. - If MANUAL – use the 5 small knobs to set frequency.
-
RE: Ramp start?
Did you bother to read my post to you ! At no time have you mentioned the “Idle Detent”
Yes.
-
RE: Ramp start?
I tried the ramp start again. I get to where the JFS switch automatically toggles off. As soon as that happens the RPMs go to zero and nothing else happens - I can’t turn on the HUD, DED, ect.
-
RE: Ramp start?
Just to clarify…
I hear a click which I assume is the JSF switch automatically shutting off?
During this time I look for RPMs to increase - I’m looking at the right front panel with different gauges which includes a small RPM gauge around the area where the fuel gauge (has 2 needles) is?