BMS Device Setup Guide Change 2
2-7
“To make the key file (in specific: the DX code lines) work a specific order of the devices is necessary. Otherwise you run into trouble. As we do not know which and how many devices you have installed the DeviceSorting_Example.txt should give you a short overview how the first code lines in your DeviceSorting.txt should look like.”
“To make the key file (specifically: the DX code lines) work, a specific device order is necessary, otherwise you can run into trouble. As we do not know which, or how many devices you have installed, the DeviceSorting_Example.txt should give you a short overview of how the first code lines in your DeviceSorting.txt should look.”
2-8
“I f you need an additional print layout for the keyboard please refer to …\Docs\01 Input Devices\01 Keyboard Layouts…”
“If you need an additional print layout for the keyboard please refer to …\Docs\01 Input Devices\01 Keyboard Layouts…”
2-10
“Pibuilders may see that different…”
“Pit-builders may see that differently…”
“We will only describe how to setup your devices via DX as much as possible. If intend to set it up using keystrokes, please refer to the vendors programming software manual.”
“We will describe how to setup your devices via DX as much as possible. If you intend to set it up using keystrokes, please refer to the vendors programming software manual.”
2-10
“Therefor it was necessary work out some strict naming conventions to make it clear what the purpose of a function is.”
“Therefore it was necessary to work out some strict naming conventions to make clear the purpose of a function.”
3-56
“Please refer to CH’s installing instructions.”
“Please refer to CH’s installation instructions.”
3-58
“Select you main Input device from the drop down list.”
“Select your main Input device from the drop down list.”
3-61
“Depending on how many device you have connected you should press one button of each device.”
“Depending on how many devices you have connected, you should press one button on each device.”
4-107
“So, in order to safe you some time you can skip it for now and instead read it if you need to.”
“So, in order to save you some time you can skip it for now, and only read it if you need to.”
4-107
“The main Input device is always the controller providing axis for pitch and roll input, namely the Stick. There are HOTAS versions out there which provide a combined unit of Stick and Throttle, e.g. the Saitek X-45 or the TM Cougar. In this case you must select the X-45 or Cougar as you main input device in the Setup Controllers screen in BMS like shown in the picture below:”
“The main Input device is always the controller providing axis for pitch and roll input, namely the Stick. There are HOTAS versions out there which provide a combined unit of Stick and Throttle, e.g. the Saitek X-45 or the TM Cougar. In this case you must select the X-45 or Cougar as your main input device in the Setup Controllers screen in BMS, as shown in the picture below:”
“On the other hand there are also HOTAS systems which have two controller units (Stick and Throttle) like it is the case for TM Warthog. In this case you must select the Stick.”
“On the other hand there are also HOTAS systems which have two controller units (Stick and Throttle), as is the case for TM Warthog. In this case you must select the Stick.”
4-110
“These tabs provide a list of all available in-game axes. Depending of the nature of the axis, each of these axes may have one of the following controls:”
“These tabs provide a list of all available in-game axes. Depending of the nature of the axis, each of these axes may have one of the following controls: (Shown opposite.)”
4-111
“It might happen that an axis is not available at the corresponding drop down list because it simply is assigned somewhere else.”
“It might happen that an axis is not available at the corresponding drop down list simply because it is assigned somewhere else.”
4-112
“The only way to solve that is that you go through all four control setting pages and search for the throttle axis.”
“The only way to solve that is to go through all four control setting pages and search for the throttle axis.”
4-113
“We also provide a DeviceSorting_Example.txt to show you how the order should look like in your DeviceSorting.txt.”
“We also provide a DeviceSorting_Example.txt to show you how the order should look in your DeviceSorting.txt.”
“1. On a short button press (>200ms) it has the real functionality as the Pinky button on the stick.”
“1. On a short button press (>200ms) it functions normally as the Pinky button on the stick.”
4-114
“Note: Since 4.36 BMS also supporst devices with up to 128 buttons.”
“Note: Since 4.36 BMS also supports devices with up to 128 buttons.”
4-115
“This is also the case if you use in addition rudder pedals.”
“This is also the case if you use rudder pedals.”
“How DX devices are programmed via the key file is explained in depth in the chapter 10 and in short in chapter 2 of the BMS Technical Manual.”
“How DX devices are programmed via the key file is explained in the BMS Technical Manual, briefly in Chapter 2, and in more depth in Chapter 10.”
“One tool to help you setting up your devices the full DX path is the Key File Editor, located in the …/Docs/01 Input Devices folder.”
“One tool to help you set up your devices using the full DX path is the Key File Editor, located in the …/Docs/01 Input Devices folder.”
“If the issue persists and you can rule out #1, #2 and #3 please feel free to report your problem, preferable in this public forum thread.”
“If the issue persists and you can rule out #1, #2 and #3 please feel free to report your problem, preferably in this public forum thread.”
6-141
“This switch in CAT III position stets an AOA (Angle of Attack) limit depending on the loadout (e.g. bombs, wing tanks are carried) to prevent damages to the jet. CAT I is for pure A-A loadout and has no limits.”
“This switch in CAT III position sets an AOA (Angle of Attack) limit depending on the loadout (e.g. bombs, wing tanks are carried) to prevent damage to the jet. CAT I is for pure A-A loadout and has no limits.”
Sorry this is so long…
I would guess that the author does not speak English as their first language so I have taken the liberty of tidying up some sentences to make them read more naturally. Please feel free to ignore these corrections if you would prefer.