X55 keyfile -BMS -Full DX Programmed
-
This post is deleted! -
X-55 key file full DX programmed with all important HOTAS functions without the need of having a SST profile active. ….
Nice!!
Good Job!
-
This post is deleted! -
-
711 Turan
I Have edited Snelle’s HOTAS profile in reverse,I’m having the same problem as you,
So I have edited it and all is good now,
I keep the POV switches for Views and use the Trim Hat switch as DMS (unshifted),Trim(shifted)I have the profile if you want it
-
This post is deleted! -
This post is deleted! -
This post is deleted! -
This post is deleted! -
really infuriating that none of the setups work for me, i’ve tried several and they all seem to get jumbled up at some point.
-
really infuriating that none of the setups work for me, i’ve tried several and they all seem to get jumbled up at some point.
Please explain what you mean by “get jumbled up”. Someone may be able to help with more information.
-
Please explain what you mean by “get jumbled up”. Someone may be able to help with more information.
none of the buttons\toggles are mapped correctly.
Trigger comes out as RDR CURSOR - Cursor enable
SW2 Trim up - Nose Down
both buttons on the front of the throttle come out as Slap Switch
and so it goes for all of them.At this point i think i need to sit down this weekend and just set it all up. But its been years since i played, and i didn’t have a HOTAS then, so i don’t know the controls well enough to be comfortable with what i need and where it should go.
But if anyone has some input on cause or a solution i’d be very grateful. -
none of the buttons\toggles are mapped correctly.
Trigger comes out as RDR CURSOR - Cursor enable
SW2 Trim up - Nose Down
both buttons on the front of the throttle come out as Slap Switch
and so it goes for all of them.At this point i think i need to sit down this weekend and just set it all up. But its been years since i played, and i didn’t have a HOTAS then, so i don’t know the controls well enough to be comfortable with what i need and where it should go.
But if anyone has some input on cause or a solution i’d be very grateful.Each button has to be individually programmed. What button does what is up to your personal preference. Some people use profiles that already has been made and all you have to do is load it through your “Setup” tab.
-
deleted
-
none of the buttons\toggles are mapped correctly.
Trigger comes out as RDR CURSOR - Cursor enable
SW2 Trim up - Nose Down
both buttons on the front of the throttle come out as Slap Switch
and so it goes for all of them.The problem with you guys is that you do not read and not really try to understand what is going on in your setup. You have controller id swapped, I explained allready and gave a few possible workarounds you can read in previous threats.
This can be found when opening the keyfile and what you see is the assignment of Button1 for device 1 and 2.
Doing some reverse engineering makes it easier to understand so here we go.
SimTriggerSecondDetent 0 -1 -2 0 0x0 0 “simtrigger2nd” “But.1” >>>unshifted device#1
SimCursorEnable 32 -1 -2 0 0x0 0 “CURS.ENABLE” “BUT.1”>>>unshifted device#2
Isn’t that what your problem is all about?
The number right after the call is your DX assignment on stick controller, swap 0 with 32. In fact that’s excaclty what you have to do with all of them. swap 0-31 with 32-62. And of course to with the shifted.I recommend to read and understand what is written in the Keyfilemanual and can be found in docs folder, do it together with my keyfile at hand (if you like it) and go from there. Simply open it with a text editor and look at the bottom section. Take in mind that windows swapped id device#1 and #2 so you have 2 possibiltys to make yours work, change the ID of controllers in windows or reprogram (in fact just renumber) the calls in the keyfile accordingly to ID order. I’m not going to for you as I am to lazy :D.
AT last but not at least, just for the record, sorry no offense : :rtfm:
-
For your info,joyid did not work for me,I tried the registry but still unsuccessful,so i just reprogram
Thanks -
For your info,joyid did not work for me,I tried the registry but still unsuccessful,so i just reprogram
ThanksYou still have the option to do a full uninstall per advise Saitek.
Do read the Readme.docx in the downloadable package. -
This post is deleted! -
I’ll do some more testing tonight. Started work late today and yesterday, had great plans for 3-4 hours uninterrupted trial and test, only to have the power company show up to do line work outside and pull my power from 0930 to 1400-ish both days.
-
https://www.dropbox.com/s/krrwgyfeba9jrqi/DINIE2.key?dl=0
here you go, key file x55
thanks to shnelle
it worked flawlessly, thank you.