Morphine's Profile
-
I’ve been trying to use Morphines’ Warthog profile. I am encountering a flight control issue that is related to my Thrustmaster TFRP. It seems the rudder pedals come across as Thrustmaster combined. I believe there is an issue with a lack of axes in Thrustmaster combined.
I discovered that when I created a profile in the Target GUI that only included the stick and throttle - the two devices appeared in BMS as Thrustmaster combined. The rudders came across as a separate device.
I tried to look at Morphines TMC file to see if there were any devices defined besides the stick and the trottle but did not see anything besides the stick and throttle. Does anyone have any ideas?
-
Ok, I think I figured it out. I took a look at the GUI profile in script form. It specified “no TFRPRudder”. That solved the issue. The rudder appeared as a separate device.
-
Hey B2Blain,
I’ve been trying the same thing with my thrustmaster pedals, they keep coming up combined. So you think you could send me your profile so I can get it working right? Right now I have to unplug the pedals run the profile in the target GUI and then plug them back in to get them separate from the combined. Thanks Rhino
-
Does any one know how to keep rudder pedals as the own indenty. I just picked up a set of Thrustmaster TFRP t-Rudder pedals. Now I’ve edited the script in the target UI but they are still combining with the throttle. So when I go into BMS UI they don’t show up but they are connected to the throttle. Right now what I do is unplug the rudder pedals before running script and then plug them back in and everything is ok. But there has to be a way to get around this without the hassle of unplugging and plugging in. Any Ideas?
Thanks, Rhino 185th
-
Hey Rhino,
Place this in Morphines script using the script editor at the beginning with the other lines excluding devices:Configure(&TFRPRudder, MODE_EXCLUDED);
I found it by selecting only stick and throttle and looking at the script in the GUI. Thrustmaster support was not help.
-
Anyone know how to get out of dogfighting mode. My element took out two SAM sites and were jumped by Mig-29s. I panicked and put it in dogfight mode and couldn’t get out. I found one post about hitting the c key to cancel. But I think Morphines key file is different.
Update 1: The “c” key is the override key. But that doesn’t work. I was able to get the FCR to change modes to RWS. But cannot get the dogfighting symbology off of the HUD.
Update 2: I figured out what was wrong. There must be an issue with Morphines’ key file or profile. The “c” key was not working. I used Boxin’s profile and key file and was able to get it to work.
Thanks,
Blain -
Hey B2Blain, Thanks so very much. Works like a charm. Now I don’t have to go through unplugging and plugging back in. I really appreciate it. I had try to rem it out also but that did not work either. Yours works Great.
Regards, Rhino
-
Hey B2Blain, Thanks so very much. Works like a charm. Now I don’t have to go through unplugging and plugging back in. I really appreciate it. I had try to rem it out also but that did not work either. Yours works Great.
Regards, Rhino
I’m glad to help. This forum is a great resource. Before I had the TFRP I had CH pedals which I couldn’t get to work in BMS. I returned them and got the TM pedals thinking it would be compatible with TARGET and have less issues. Then spent several nights trying to find out why the jet was drifting so much. Like I said TM is of no help. There solution is to send you a link to the manual.
-
Challenge Accepted!
This is also something I’ve wanted to do for a while as well. Add the code below to the TARGET Script and the 1st (Top) LED will come on once you are in the deadzone and the remaining lights will come on once you leave the deadzone and activate the AB. In your controller setup screen set the AB detent when the first light is on and you will be good to go.
Add the code below between the following two lines in the TARGET Script:
SetShiftButton(&Joystick, S3);////////////////// AXIS CONTROLS //////////////////////////////
////////////////// LED CONTROLS ////////////////////////////// //initialize LED status all "OFF" ActKey(PULSE+KEYON+LED(&Throttle, LED_ONOFF, LED_CURRENT-LED1)); //set LED 1 OFF ActKey(PULSE+KEYON+LED(&Throttle, LED_ONOFF, LED_CURRENT-LED2)); //set LED 2 OFF ActKey(PULSE+KEYON+LED(&Throttle, LED_ONOFF, LED_CURRENT-LED3)); //set LED 3 OFF ActKey(PULSE+KEYON+LED(&Throttle, LED_ONOFF, LED_CURRENT-LED4)); //set LED 4 OFF ActKey(PULSE+KEYON+LED(&Throttle, LED_ONOFF, LED_CURRENT-LED5)); //set LED 5 OFF //LED Throttle Position Indicator; LED 1 - MIL Power; LED 1-5 AB KeyAxis(&Throttle, THR_LEFT, 0, AXMAP2( LIST( 0, 65, 75 ), LED(&Throttle, LED_ONOFF, LED_CURRENT-LED1), CHAIN( LED(&Throttle, LED_ONOFF, LED_CURRENT+LED1), D(), LED(&Throttle, LED_ONOFF, LED_CURRENT-LED2), D(), LED(&Throttle, LED_ONOFF, LED_CURRENT-LED3), D(), LED(&Throttle, LED_ONOFF, LED_CURRENT-LED4), D(), LED(&Throttle, LED_ONOFF, LED_CURRENT-LED5)), CHAIN( LED(&Throttle, LED_ONOFF, LED_CURRENT+LED2), D(), LED(&Throttle, LED_ONOFF, LED_CURRENT+LED3), D(), LED(&Throttle, LED_ONOFF, LED_CURRENT+LED4), D(), LED(&Throttle, LED_ONOFF, LED_CURRENT+LED5)) ));
If you’ve changed the deadzone to something other than 65 - 75, you will need to adjust the vaules in the text “AXMAP2( LIST( 0, 65, 75 )” accordingly.
I love the mods to your profile but I can’t seem to get the LEDs to light up when going into AB. I don’t know if it an AXMAP issue with the dead zone - I’ve posted the script from my profile below. As I understand it, after I have ran the profile I go into BMS set up. Load the appropriate key file, then set the AB when the light comes on. I’m assuming you are referring to the fifth light in the column at the top of the trottle. The fifth light is off. I push the throttle forward and the light never comes on.
MapAxis(&Throttle, THR_LEFT, DX_ZROT_AXIS);
SetCustomCurve(&Throttle, THR_LEFT, LIST(0,5, 65,70, 75,70, 100,100)); //start at 5% for idle cuttoff & create a deadzone between 65% and 75% for ABMapAxis(&Throttle, THR_RIGHT, DX_Z_AXIS);
SetCustomCurve(&Throttle, THR_RIGHT, LIST(0,5, 65,70, 75,70, 100,100)); //start at 5% for idle cuttoff & create a deadzone between 65% and 75% for ABThanks!
-
Hello,
Just installed your profile, everything seems to work accordingly except the China ht (the red one on the throttle) where it should be the range knob. It doesn’t work in the game and even when using the event tester it doesn’t show any output.
Could you help ?
-
I just read your question and ran my profile and the china hat works fine. In the device analyzer it should show button 11 and 12 being lite. Maybe try to download the file again because you never know. I’ve been using the profile for a year with no problems.
Rhino
-
Does anyone have a copy of the latest ver of the profile please Morphs page says not up to date get from others.
So are there any OTHERS out there with the latest ver please -
Does anyone have a copy of the latest ver of the profile please Morphs page says not up to date get from others.
So are there any OTHERS out there with the latest ver pleaseI “think” this is the last updated one. It’s in this same thread just ~10-15 pages back.
https://www.benchmarksims.org/forum/showthread.php?8147-Morphine-s-Profile&p=340494&viewfull=1#post340494 -
Thanks for that . Wasn’t sure it was right one with it being older than when the 4.33u2 was released just going through the updates to get the LED’s working
-
This is my version which works in 4.33U2. It also uses the new QWERTY US/Int keyboard layout which was introduced in 4.33. The Original Morphine’s profile used a version of Dunc’s keymap. This was missing some of the new key functions implemented in the latest versions of BMS. a PDF Keyboard layout is included in the dropbox. The throttle afterburner lights work too. Just make sure to set the proper order in devicesorting.txt
link to dropbox of profile ect.
https://www.dropbox.com/sh/4l2j2sbbkkmwoaa/AAAMks8YYDvUsOQ6vr7bi5bia?dl=0 -
Thanks for that Makes more sense now.
I’m just dipping my toe into the waters of target software trying to workout if it’s possible to do a second function on the CMS right in the GUI editor for a if you hold the key for say 2sec you get another key press.
I hope that makes sense I have read the basic manual but carn’t find or just plain missed it I think it is a H or hold function but would be grat if somone could point me in the right direction of what to read and where to read If I can uderstand how it works then I think I can do the rest but very new to the whole scripting thing any help would be great -
I don’t know how to do it in the GUI editor but the script command is TEMPO. The GUI is simply a pretty interface for automatically writing a (an ugly) script. You could extract the auto-generated script from the GUI and manually edit in the TEMPO command but probably there is a way to do it in GUI directly.
-
Ok I Think I may be going a little mad I have loded the keyfile and the script set the script running first then load up falcon. Now this is where it gets fun I’m using the files found above.
Most of the throttle works great but my stick no not so I have no TMS DMS CMS functions or trigger etc and no shift function either!!!
AM i BEING DUMB??? I HAVE HAD A LONG LAY OFF FROM FLYING REGULAR BUT IS THE A COSMIC BLOODY FORCE TELLING ME I’M NOT MENT TO FLY
Right rant over sorry. I have a warthog and falcon patched upto U2. This should be easy people keep telling me All I want to do is fly online with friends but without my keys working I dont want to waste other peoples flying time trying to get me up and running.
Someone please help this is getting me to the point of going to DCS but F4 is my true love -
Ok I Think I may be going a little mad I have loded the keyfile and the script set the script running first then load up falcon. Now this is where it gets fun I’m using the files found above.
Most of the throttle works great but my stick no not so I have no TMS DMS CMS functions or trigger etc and no shift function either!!!
AM i BEING DUMB??? I HAVE HAD A LONG LAY OFF FROM FLYING REGULAR BUT IS THE A COSMIC BLOODY FORCE TELLING ME I’M NOT MENT TO FLY
Right rant over sorry. I have a warthog and falcon patched upto U2. This should be easy people keep telling me All I want to do is fly online with friends but without my keys working I dont want to waste other peoples flying time trying to get me up and running.
Someone please help this is getting me to the point of going to DCS but F4 is my true loveHave you edited your devicesorting.txt in your BMS install? The thrustmaster combine needs to be at the top of the list.
-
Hi all
Having fun with the Profile Files Gastone Provided in the dropbox Link.
Works great for me in the “mud moving” process.
I have Two Quick Question regarding A-A duty:
1. Is there a Hotas Function for Switching RWS to TWS, or that OSB Button?
2. IS there a Hotas Function for FCR Range, or are we all used to slew the Radar cursor to up and down boundaries to switch?Thanks in advance
Foss