Falcon only showing up on one monitor….
-
did you configure Nvidia surround?
-
did you configure Nvidia surround?
Of course. All screens working and sync together.
Sent from my SM-T350 using Tapatalk
-
If you’re eyefinity or surround then when you maximize something like a web browser it will stretch wall to wall without regard for the fact that you have specific monitors. If that’s not happening BMS won’t fullscreen to the display.
Second, check for resolutions reflecting your massive combined display in the BMS options. If you set a lesser resolution then it won’t work like you expect.
-
Maybe try window mode.
Στάλθηκε από το MI 5 μου χρησιμοποιώντας Tapatalk
-
Not mentioned yet but you are going into 3D correct?
The GUI will only show on 1 monitor, then will expand to all 3 when you go to fly.
Currently running 5910x1080 on 3X Acer’s with Nvidia Surround and that’s how it works for me. -
No, I’m not in 3D…hmmm, something to check out.
-
U r not in 3D?
Man GOTS. [emoji38]Στάλθηκε από το MI 5 μου χρησιμοποιώντας Tapatalk
-
Well get in 3d and see if it displays on all 3 screens. As said the UI will display only in the center monitor. The UI is in 1024x768 and u can’t change it. But once u get in a mission in 3d in the cockpit u should be fine.
Στάλθηκε από το MI 5 μου χρησιμοποιώντας Tapatalk
-
After much effort through trial and error, I’m still unable to get BMS to span across all three screens. I’m confident that it is a simple matter to alleviate my dilemma. I’ve tried the suggestions given but there is no joy. I do understand that the UI screen is set for one resolution. I’ve tried in Instant Action as well as Campaign mode…no joy.
It took me a couple of hours to figure out how to do a screen capture in Windows 10, so I can post screens of my Nvidia Control Panel. I present the following screens for viewing.
Perhaps these will help give insight to my lack of knowledge in this matter.
-
What options do you have in the setup screen of the sim? (like shown in the selection on page 34 of the BMS-Manual.pdf, located in \Falcon BMS 4.33 U1\Docs\Falcon BMS Manuals)
-
-
Looks correct. If it’s not doing what you want then what is it doing?
Is it replicating 1920x1080 on each screen, only one screen? Other screens black? Other screens desktop? Any indication of windowing? Is alt-tab slow with black flicker or instant?
All I can think is maybe some automatic nVidia game profile is recognizing Falcon and overriding?
-
BMS only appears in the center screen. Other two screens remain black. Not slow, game loads fast.
-
If u disable display surround?
Also which drivers? U might need to uninstall and use older drivers.
Which windows we said u r?Στάλθηκε από το MI 5 μου χρησιμοποιώντας Tapatalk
-
If I disable surround, I have only one screen.
Current driver is 398.82
I have Windows 10…if that is what your asking. -
Sorry my card is old and doesn’t support surround.
But if u disable surround u will still should have 3 monitors as I do.
U extend to the other monitors.
I use softh which actually must be like surround.
Have you disabled full screen optimization?
Have you tried older drivers with clean install?Στάλθηκε από το MI 5 μου χρησιμοποιώντας Tapatalk
-
BMS only appears in the center screen. Other two screens remain black. Not slow, game loads fast.
While fullscreen should absolutely work you might find that windowed mode works and is just as good. I would try windowed.
Also, another idea: Are any files in your \user\config directory write protected? Is dx9display.dsp? Perhaps deleting dx9display.dsp and allowing Falcon to re-make it will reset things.
-
This sounds stupid, but have you gone into display settings in Win10 and made all your other two monitors be in extended mode? I have a gtx1060 and the same three Asus monitors you have and have had windows not allow them to be detected even when configured in the Nvidia Control Panel as one screen in surround. Also, in game setup, graphics you should be able to select a higher quality level then “0” which seems to give me a better outside view.
-
Just a long shot, but it might be related to the Win10/resolution bug that’s going around. If the resolution is not switching BMS will obviously not display on three monitors. Just a thought ……
https://www.benchmarksims.org/forum/showthread.php?33518-Bms-launches-in-low-resolution-(not-menu)
-
Just a long shot, but it might be related to the Win10/resolution bug that’s going around. If the resolution is not switching BMS will obviously not display on three monitors. Just a thought ……
https://www.benchmarksims.org/forum/showthread.php?33518-Bms-launches-in-low-resolution-(not-menu)
I’ve Got three screen now!!! Your suggestion has seem to foot the bill. Now I think I have to adjust my FOV. Was setting pretty close to the Hud.