Fish's VoiceAttack commands
-
Hi all
I have downloaded Fish’s VA profile but inside the zip file there isn’t a list of commands that the profile recognizes.
I am fairly new to VA and would like to know if there is a list of commands that this profile recognizes.
I did manage to see the commands that VA listens for be editing the profile as well as by trial and error.
For Example, I can’ seem to issue any wingman commands.
Thanks for any tips on using this profile with VA, as well as an VA tips in general!
Cheers
-
As an example, try this:
say Wing
Combat 1
then pick a command from the on-screen menuor
Wing
Formation 1
then pick a command from the on-screen menuIf you have not already, watch his video:
I’m not sure which of his profiles you may using, but he explains he uses the attached command approach.
GC
-
@CaptCanada
You must read the readme first.txt in the pack, and always use the latest pack, for the latest BMS. and as @greatcouloir said, video is best starting point. -
@Fish44 Hello, please was using voice attack normally, But recently I realised that when i request for overhead approach, it responds with straight in approach, even though in the voice attack in written overhead approach. Am using Fish’s Profile 4.36. I’ll be glad if you help me out
-
@greatcouloir thanks. After studying the picture and watching the video, I’ve been able to figure it out. It doesn’t seem very intuitive initially as you have to drill down a few menus to get the command you want instead of just saying it directly.
Still a good profile though
-
@Sniper-0 Have you followed the instructions to install the profile, including those suggested in my post above. ?
-
@Fish44 I tried reinstalling, but the app refused to work totally
-
Thanks to Fish for his wonderful and very useful profile. I tried other profiles also, but Fish his VA profile works best for me.
One small remark… just a view voice comms aren’t correspondending with the commands. Fish already responded on my remarks immediatly and of course very appreciatedThough Fish advised me to replace/overwrite again his menu.dat file (Falcon BMS 4.37 U2 ‘Data/Art/Cockpit Art’) over the original Menu.dat file (from the original installation/backup folder of BMS) some of the commands are different, or still not working. No biggie, 'cause without VA commands can also be given. Still, below a description of the commands that differs and maybe some more users of Fish his profile has the same?..
When holding short on the runway and ready for departure: ‘Tower’ (menu popsup) ‘Ready for departure’ (menu disappeares), but no confirmation from the Tower (‘You’re cleared for take off’) follows.
When airborn and contact ‘Departure’ (switch to UFH 4) the ‘Common’-menu popsup with ‘QNH’, instead of the menu ‘Airborn’
When contacting ‘Approach’ (menu popsup) and make the voice comm ‘Unrestricted Approach’, no confirmation from the approach/tower follows -
@Nick-san said in Fish’s VoiceAttack commands:
…some of the commands are different, or still not working. … When airborn and contact ‘Departure’ (switch to UFH 4) the ‘Common’-menu popsup with ‘QNH’, instead of the menu ‘Airborn’…
Hi Nick,
First step is to check that you are working with the correct 'menu.dat file (…BMS4372\Data\Art\CkptArt\menu.dat). You should open it with a text editor and navigate down to the ‘#menu ATCMsg AiNoExtent 8 0 white ATC COMMANDS’ section, and make sure it matches the screen below. Then open you profile with voice attack (Should be called BMS4372VAFish), and choose ‘EDIT’ then navigate and double click on the command ‘A T C Depature;Air Traffic Control Depature; Departure’ (under the A T C category. ) And make sure it looks like the image. If there’s a mismatch, then you may have to download the V6 profile again. -
This post is deleted! -
It works!!! 100@. Have re-installed BMS, VA and your profile and everything works perfect. Thank you and I’m very happy
-
I recenty intalled this profile. Very helpful that the coms meny pops up on screen.
I am having some dificulties with executing some orders. For example “Two Combat One” pops up during a dogfght but I cant execute any command, whether weapons free or any of them on the list…
How come? Where can I read what I have to say?