@Icer:

I must be missing something, I set my Warthog throttle up in Alt Launcher Axis Assign and it couldn’t be easier.

Select “Assign” for Throttle, pull back to Idle Detent stop (top pic), click “Idle Detent” button. Push throttle forward to the AB stop, click “Set AB” button. Save and done. Push past the AB stop and bar turns green and says “AB”, lift past Idle stop and bar turns red and says “Idle Cutoff”. Just be sure you have full travel (if not increase Saturation until bar is full)

When you setup your Throttle in AL are you using Throttle or Throttle Right? When I get to the Idle stop Asix travel is at zero.

Hello all, I have a question on setting up the Idle Cut off on the Throttle. I am using BMS 4.35 and in the Config I have Idle cut off checked. I am using Alt Launcher. Setting the After Burner no problem but the Cut off is the problem. When I get to the Idle I can’t set the Idle detent. When I go pass to OFF it doesn’t register. OFF | | Idle To get the Idle detent to work I have to go a forward little pass Idle and set Idle detent. The throttle travel on Alt Launcher goes is from the Idle to full forward but dose not register pass | Idle. Is this how it works or am I missing something?

Disregard I found it.

Where do you get it?

All, I hope someone can help me.
1. This is what happen I have been using Falcon BMS 4.34 with Alternative Launcher v1.40 no issues.
2. Two days ago I installed Falcon BMS 4.35 and today I installed Alternative Launcher v1.50 It did not remove the old version and the old version still works with BMS 4.34 but when I launch BMS 4.35 it dose not launch ALT 1.50 but when you to the icon properties it has \Falcon BMS 4.35\Launcher.exe.

I know I must have did something wrong but what?

All, never mind I got the answer that I was looking for.

I am trying to use UOAF Advanced VoiceAttack Profile – Including Ownship Callsigns
Ok I am a total rookie on using VA. I downloaded the profile and try to use it with my Warthog but nothing happens. But I am new to VA. I need setup help. I am using a Thrustmaster Warthog.
1. I go into settings and go into Joystick Options and Enable Joystick 1 and Enable POV Switches.
2. Under POV 1 switches what do I select? Also which POV the one on the side of the Throttle or in front? For now I am using the POV on the side for UHF up and VHF down.
3. Hotkeys is set for Push listen Left Alt +F2 do I have to make any changes here? I really don’t understand how this works.
4. Joystick Button Recognition what should I set to? Toggle listening start / stop, VoiceAttack listens while buttons are down or other?
I am using version 1.83 and I am using Alternative Launcher to setup my HOTAS

Ok I am a total rookie on using VA. I downloaded the profile and try to use it with my Warthog but nothing happens. But I am new to VA. I need setup help. I am using a Thrustmaster Warthog.
1. I go into settings and go into Joystick Options and Enable Joystick 1 and Enable POV Switches.
2. Under POV 1 switches what do I select? Also which POV the one on the side of the Throttle or in front? For now I am using the POV on the side for UHF up and VHF down.
3. Hotkeys is set for Push listen Left Alt +F2 do I have to make any changes here? I really don’t understand how this works.
4. Joystick Button Recognition what should I set to? Toggle listening start / stop, VoiceAttack listens while buttons are down or other?
I am using version 1.83 and I am using Alternative Launcher to setup my HOTAS

Hello to everyone again and happy holidays. I have most my new Warthog setup so now I trying to get Voice Attack to work correctly on my system I am using someone’s profile I forgot who it is it look good my I have a question Joystick options. I am using Throttle side POV UHF and VHF now if I understand I would have to go into Joystick Options and set this in Voice Attack, is that correct?

I got a lot thigs setup now but I looking for a way to use Left Throttle button as a track IR re-center and it reads see 6.06 but when I check the Doc’s I can’t find anything on the subject. I must be missing something. My track IR is set using F12 and I want to use Left Throttle button.