Thank you.
But I found solution. In Falcon BMS Config, under Hardware there is Iddle Cutoff position. And it was marked.
Now I changed it to unmarked and everything works fine
Posts made by Smok
-
RE: Cut off/idle in Warthog -what to do to run, not burn engine (F 4.34)
-
Cut off/idle in Warthog -what to do to run, not burn engine (F 4.34)
First of all, I would like to thank you for the next super incarnation of Falcon.
But I have problem, could you help me please.
I use BMS - BasicDx TM Warthog_MFD file (Falcon BMS 4.34/Docs/01 Input Devices/03 Hotas Setup/TM Warthog.
All axes work fine in the setup screen.
During ramp start, I switch JFS switch to start2 position, observe RPM, at about 20%, the SEC caution light goes out, and I try to cut off/idle detent pushing L/G WRN SILENCE (gray button on the warthog throttle - according to BMS - BasicDx TM Warthog MFD profile file) and there is no reaction, soon the RPM goes to zero and FTIT increase and I burn the engine, pushing again the button when FTIT increase do nothing.
The same effect is when I use Alt+i, or even when I try to use throttle (right or left, or both, of course first I assigned the move from off to iddle in the setup screen).
I also try to move throttle all the way forward and then all the way backward as a first thing siiting in the cockpit - no effect.Of course in the setup screen all methods show that the cutt off/idle detent toogle works fine.
What is wrong, could anybody help me please. -
Profile for T Warthog + T rudder pedals + 2 T MFD needed please
I am new user of Thrustmaster Hotas Warthog (stick and throttle) + Thrustmaster rudder pedals + Thrustmaster MFD (thats the newest part of my equipment). First I used Warthog + pedals without target profiles and configure everything inside Falcon
s setup. It worked fine. But now I would like to use full potential of my hardware and try to upload profile via Target software. I started with Mud
s profile, but without effect, then with Rybo`s V 2,5 - stick and throttle works, but without rudder.
Could anybody help me please and send good profile for such hardware?
I will be gratefull fo help. -
RE: Win 10 migration
Also for me (win 10 64 bit, falcon 4.32 and 4.33 - no problem)
-
RE: Fallon-Nevada Theater discussion
There are already many theaters in BMS and surely they emphasize true and indisputable value of Falcon/BMS as a prime simulation … simply enjoy them and also contribute to their improvement by giving constructive comments and suggestions.
I enjoy Falcon from the beginning (1998 )
It is my favourite sim, but Nevada was my favourite theater. -
RE: Fallon-Nevada Theater discussion
DCS Nevada is in pre-purchase stage and what about Nevada BMS?
-
How can i change the keys - I could in the past but coul not now.
I have a problem.
Maybe anybody could help me please.
After more than half a year i install again F BMS 4.32 1-7. But there is a problem with changing keys.
I have toshiba qosmio laptop i7, geforce 560mx, win 7 64bit and i had no such problems earlier.
When i try to change keys in setup tab (current key file BMS) and press key on the left side of a key table (with left mouse click) , it turns blue, then i press the desired key but nothing happend, nothing changes.
But if i do it with stick (T Flight hotas X) - press a key on the left side of a key table, it turns blue, then press a button on the stick and it works perfect.
I want to move radar cursor up, down, left and right with arrows buttons on the keyboard, but could not.
I reinstall falcon twice, install newest nvidia drivers, check system with kaspersky internet security but it do not resolve the problem.
I can fly but could not use radar without the ability of moving cursor and locking targets?
Any idea how to do , or what is wrong?
I will be very grateful for any help.