Waypoints are changing - different that planned
-
Guys he didn’t make a big deal out because he just mentioned the same bw for connection issue.
He doesn’t say it’s a bug if u do or problems will exist. He says some guys playing it experts advice other guys as this is a must.I have faced it also.
He just mentioned something. The making it big deal I believe started afterwards with the mentioning on this and thus making it a big deal.Never had this waypoint issue. Heard in the TS guys saying so, but mostly was few and specific occasions, probably guys messing around.
Once I recall we had all (about 20) the same issue but it was caused by fubared mission file.Sent from TapaTalk
-
Guys he didn’t make a big deal out because he just mentioned the same bw for connection issue.
He doesn’t say it’s a bug if u do or problems will exist. He says some guys playing it experts advice other guys as this is a must.I have faced it also.
He just mentioned something. The making it big deal I believe started afterwards with the mentioning on this and thus making it a big deal.Never had this waypoint issue. Heard in the TS guys saying so, but mostly was few and specific occasions, probably guys messing around.
Once I recall we had all (about 20) the same issue but it was caused by fubared mission file.Sent from TapaTalk
Lost in translation, Arty. My apologies to you, but I am going to refrain from explaining it. I’ve made my point and will not discuss it any further.
-
@Cloud:
Who are you to tell people what they should and what they shouldn’t do or say.
If you want to contribute to the myth - which I have literally heard that “No…no, you have to doubleclick the ATO, once isn’t enough” then you are welcome to do so.
You shouldn’t, because that’s not accurate, but if that’s the kind of advice you’d like to give; I can’t stop you.
You and others have blown a simple remark greatly out of proportion. Please feel free to continue your crusade against accurate information, but I’m out.
-
…. I’m not sure as to the veracity of AMVI_Hawk’s statements regarding the potential to save an “empty” DTC, as I have not had that experience. If you have a critical target, I’d write down the pertinent information on a piece of paper.
I assure you it happened to me when I saved lines, TGT STP without haveing previously loaded my DTC.
I am not sure if it was strictly related to avoid of load of DTC but since that time I always try to remember to me to follow those steps.
However, maybe, I could have done something wrong out there…… but the procedure I mentioned will not fail and, for sure , paper and pen are always on my charts.Tail widd and clear sky
Kind regards
-
Hi,
I have already met this kind of issue: you have to clear all target steerpoints …sometimes, target steerpoints are kept from the previous mission and the order of waypoint changes once the DTC is loaded in rampstart.
so now, we are used to check the DTC before save in 2D GUI
Br
-
Hi all,
I played around a bit and what sukhoi69 suggested did the trick. It’s not about clicking flights (or even double clicking ) - I found out that DTC contained old targets and that messed my flight plan. Reset targets, setting new target in recon and saving DTC was enough to get rid of problems.
Thanks a lot to all who helped!
Av.Hi,
I have already met this kind of issue: you have to clear all target steerpoints …sometimes, target steerpoints are kept from the previous mission and the order of waypoint changes once the DTC is loaded in rampstart.
so now, we are used to check the DTC before save in 2D GUI
Br
-
I played around a bit and what sukhoi69 suggested did the trick. It’s not about clicking flights (or even double clicking ) - I found out that DTC contained old targets and that messed my flight plan. Reset targets, setting new target in recon and saving DTC was enough to get rid of problems.
I also found very useful to reset “variable” parts of the DTC from WDP before setting it again… never missed a shot when issues arised!
-
Hi there, same issue! I have tried from WDP, but it doen’t work.
Do you reset from 2D DTC in BMS Sim, is it right? -
A click on everywhere on the map, “recon” and “clear all” should make the trick.
-
sounds like a UI update/refresh over MP issue for some been a while since I looked at that part off the code will have a look and see
-
I have this issue as well, or very similar.
Everything works perfect when I start out. Then, after swapping to AA or AG modes my steerpoints are never the same again. Extremely confusing, especially for a new guy like trying to learn lol. Over time I’ve learned to use the HSD in combination with ATC/AWACS ETC… to move around. As well, even when the steerpoints are messed up on the HUD, cycling through them while the FCR is SOI will still correctly target the appropriate steer as POI on the FCR.
If you guys need any info on this or if there is anythign I can do to help pinpoint the issue for you please let me know.
-
ok so if given the choice which sounds more correct
1, only effects clients
2, effects both host and clients
3, other (please specify)