YAME64 suite
-
Awsome setup!! Can YAME support more than one monitor to have all these gauges extracted at 3 or 4 screens?
Yes
-
Well I’ve very happy with the way it turned out. Started in January and didn’t think I would be finished this quick. I have a couple of gremlins to tackle. By the way has anyone seen where you get random key inputs? I can actually watch the controllers section of the setup menu make key inputs without touching anything.
Looking good mate!
How have you wired the switches? Sometimes ghosting can appear when using matrix setup; or sometimes key modifiers (shift-ctrl-alt) get stuck when not programmed correctly. -
I think I will try and remap all the switches again and see if that helps. I used 2165 boards from desktop aviator. Subzero, i have 3 10" and 2 7" monitors aside from the 40" 4k tv and still getting just over 60 fps. Using a GTX 1080 for the 40" and 10" screens and using the desktop graphics card for the 7" screens.
-
Focaldesign, not sure what matrix setup is. In the event that is the case, any way to prevent the ghosting?
-
Focaldesign, not sure what matrix setup is. In the event that is the case, any way to prevent the ghosting?
Matrix wiring is where you don’t use a separate + & - connection for each wire, which limits the amount of possible switch positions & overal number of switches per board, but use a matrix connection where there are common rows and common columns.
See http://www.dribin.org/dave/keyboard/one_html/ you have to add diodes to prevent ghosting. -
Nice setup, but your joystick is in the wrong place
Awsome setup!! Can YAME support more than one monitor to have all these gauges extracted at 3 or 4 screens?
Yep. Using two touchscreens for YAME here; I think someone here has 5 screens just for gauge display.
-
Yes I know, I just recently got back into flight sims and the center position of the joystick always felt more natural to me. As much as I wanted the project to be as authentic as possible, I couldn’t get away from the center position. Lol
-
Well was able to get it fixed, turned out to be a bad board. Had a spare on hand so time to get my brain wrapped around falcon again and do some flying. Thanks for all the help guys.
-
My YAME CRASHES almost every time I use it for MP sessions, and when it does, my session is lost. It also happens alot of times when I’m in SP and I have to Alt - Tab out of BMS to restart it!! I’ve tried giving this program a chance, but it keeps letting me down. Does anyone have ANY solutions to this problem, or has anyone else experienced anything like this with this program? It’s a wonderful program, but it will not continue to run for me. I’m using the latest version by the way.
FRUSTRATED!!!
-
@usafpga:
My YAME CRASHES almost every time I use it for MP sessions, and when it does, my session is lost. It also happens alot of times when I’m in SP and I have to Alt - Tab out of BMS to restart it!! I’ve tried giving this program a chance, but it keeps letting me down. Does anyone have ANY solutions to this problem, or has anyone else experienced anything like this with this program? It’s a wonderful program, but it will not continue to run for me. I’m using the latest version by the way.
FRUSTRATED!!!
Sorry to hear that mate.
I have no clue what could be causing this, but I’m far from a computer expert so not helpful I’m afraid.
We have had over 1,000 downloads so far and less then a handful of reports from continues crashes; so it’s very hard to pinpoint the possible causes. As it’s a very small minority, we doubt it’s purely on YAME’s side and most likely a combination of factors or specific versions of certain pieces of software (e.g. NETframework, VisualStudio redistributable, Windows firewall, GPU drivers)… -
Sorry to hear that mate.
I have no clue what could be causing this, but I’m far from a computer expert so not helpful I’m afraid.
We have had over 1,000 downloads so far and less then a handful of reports from continues crashes; so it’s very hard to pinpoint the possible causes. As it’s a very small minority, we doubt it’s purely on YAME’s side and most likely a combination of factors or specific versions of certain pieces of software (e.g. NETframework, VisualStudio redistributable, Windows firewall, GPU drivers)…No worries. Every system is different, I realize that. I’ll go back to MFDE while I continue to try to get it sorted.
-
@usafpga:
My YAME CRASHES almost every time I use it for MP sessions, and when it does, my session is lost. It also happens alot of times when I’m in SP and I have to Alt - Tab out of BMS to restart it!! I’ve tried giving this program a chance, but it keeps letting me down. Does anyone have ANY solutions to this problem, or has anyone else experienced anything like this with this program? It’s a wonderful program, but it will not continue to run for me. I’m using the latest version by the way.
FRUSTRATED!!!
Can you give more informations? Your system, what yame configuration are you using, hook or not… even better you can send your layout and config file.
Thank you for trying yameInviato dal mio Y635-L21 utilizzando Tapatalk
-
Hi guys,
I wanted to try this for my cockpit and started on setting it up. First of all: it looks great (and works great)!. Thanks for the hard work.
In my cockpit i use rotated screens. So it is essential for me that it is possible to rotate the MFD’s. Is that feature available? I read in the manual that the rotate function will appear with right mouse button if available. I see hide and align with grid. The rotate option does not appear for the MFDs (or i hope i might be missing something here?)thanks for your time.
greetings Snowman
-
Hi snowman,
In v1.1 (and v1.2rc) we only have rotation available for master Caution and eyebrows IIRC.
Are you sure you can’t turn your screens in Windows setup? I remember doing that with a monitor at work to have it vertical.Greetz
Faan -
Hi Faan, thanks for the explanation (and fast reply) . I will try the Windows option thx!
Snowman
-
I rotate mine in the nVidia control panel.
-
Hi Faan, thanks for the explanation (and fast reply) . I will try the Windows option thx!
Snowman
No problem.
This is how I did it on my Windows pc a while back. (not my screenshot, but that’s how it looked in Win7) -
Hi snowman,
In v1.1 (and v1.2rc) we only have rotation available for master Caution and eyebrows IIRC.
Are you sure you can’t turn your screens in Windows setup? I remember doing that with a monitor at work to have it vertical.Greetz
FaanWhat is v1.2rc? Was I asleep at the wheel when the latest version released?
-
What is v1.2rc? Was I asleep at the wheel when the latest version released?
RC stands for release candidate. It’s an internal version, more finished then beta status, but not finished to be released yet (1 nasty bug for server + multiple clients).
-
No problem.
This is how I did it on my Windows pc a while back. (not my screenshot, but that’s how it looked in Win7)that did the trick.
very simple. did not think of it thx!snowman