IAI Lavi
-
Hello,
thank you for your report and relevant point, here is my answer :
The biggest issue here is that BMS doesn’t contains any specific line of code for canards.
It means that I can only do a couple of comprises, to try to get a quite realistic position of canards.
This is where the issue is : canards position depends on a lot of factor, such as flying mode, AoA, position of gears, roll, pitch and even yaw.
I am really embarrassed, because for now, I can’t represent the approach mode for canards especially because BMS doesn’t make a difference between take-off and landing…
I tried a couple of solutions, but they were irrelevant for the rest of the flight. 5% won versus 95% !
For now, as I said, I don’t have a solution. But I am still checking for one !
Radium
-
Understood.
I thought it might be a BMS limitation.
In which case having it correct for normal flight makes more sense.Cheers
-
the canards and TEF may use two sets of Xswitch 2 or 3, to switch the DOF directions between normal flight and takeoff/landing phase.
-
@ccc1tw hello, I am afraid it doesn’t works like that !
-
Hello,
just to let you know that I am now working on :
-
Canards movements enhancement (For now, unsuccessful to get something nice, especially on landing mode). I tried a couple of solutions, issue is mostly the interactions with the other functionalities implemented. Because I do not have any control on Gx. This is the only way to differenciate flight modes, especially because Lavi uses AFM, and is not an OFM aircraft. I guess, if it was OFM only, it would be easier.
-
Afterburner : I try to have something a little bit progressive (not too much, because it is not like that in real life), but I can’t get something good. Afterburner is an additional injection of fuel which does not changes RPM, for this reason, it’s never something that slides out of the nozzle.
-
I tried to use DOF38, but it’s totally fucked up and I can’t get a nice result. I tried by both translation and scale vectors, but it doesn’t works.
-
Also, I found that this DOF is linked with these acdata parameters :
sndAbExt 39 #External high RPM & afterburner roar - Heard mostly from the rear at close and medium distance - DO NOT CHANGE "RPM" VALUES!!! - THEY ARE NOT PURE RPM BUT FROM A FORMULA TIED TO RPM & NOZPOS CHARTS! sndAbExtChart 2 1.0000 0.00 1.0300 1.00 sndAbExtPitchChart 5 0.0000 0.80 0.7000 1.00 0.9600 1.20 0.9700 1.00 1.0000 0.90
Which is really strange (I took this example from Manos’ Mirage F1 acdata).
-
I enhanced a bit the main texture file, especially the under grey part.
-
Because nothing works well, I will do some data gathering about Griffin bomb, to help my friend vAIcon to implement it into ITO.
-
No v1.0 before next week, because I want this version to be really clean.
Stay tuned !
Radium
-
-
@Radium
Good to hear this.
Because some plane especially with the canard they use them like a brake surface after the landings.
When the nosegear touch the ground the canard turn almost totally vertical to maximise the brake area.
Or the Ailerons and flaps also move out this way.The afterburner can change to use particle system instead of textures ?
-
@repvez Hi !
Thank you for your comment. Finally, I found a way to have a progressive afterburner, and I am happy of the result ! See it in v1.0 !
Coming back to canards issues.
Regards,
Radium
-
Gentlemen,
I just did a little video for you to see what I did for Lavi afterburner.
For some reason, video compression doesn’t shows afterburner textures with the finest details, but it’s good enough for now. You’ll see it soon on ITO !
Hope you will like it !
Radium
-
@Radium
Total awesomeness,
I can see flood of requests to update AB effect on other models -
Hello,
finally, I succeeded to get more realistic canards.
There is no way it would be perfect, because I have so much limitations.
I tried my best to offer you something nice, and I think it’s rather good.
I will try to improve some stuff, but it’s really hard because it’s a matter of comprises. I already tried a lot of solutions to get something smoother, and this is the best I could have got as of today.
Hope you will like it !
Radium
-
@Radium Radium = No Limit !!!
-
@Radium looks much better! Great work! Now onto the cockpit!
-
Hi !
Canards’ nightmare !
-
-
Hello everyone,
today, I am most happy to release Lavi v1.0 !
I never took so great care for a project, and, with my great friends Topolo, vAIcon, Manos1981, and the help of Toot, SOBO-87 and all my followers, I am very proud to offer you today my Lavi.
I really hope that you will enjoy it !
Click here to download :
שמע ישראל
Now, time to move to ZTZ-96 !
Best regards,
Radium
-
@Radium I’m open mouth !!!
another masterpiece
the most beautiful
because you transmitted all the passion and enthusiasm with this project
Your talent is precious for all of us
Thank you
-
Hello,
I am happy to post the first hotfix of Lavi :
1. AA missile assembly y axis was corrected and reexported + accurate parent.dat 2. Griffin bomb texture was implemented (it was forgotten in v1.0) and reexported
You can download v1.1 here :
Information : in v1.2, texture numbers will change, to match ITO architecture (vAicon will jump of joy, I bet)
Cheers,
Radium
-
Hello,
I am happy to post the first hotfix of Lavi :
1. AA missile assembly y axis was corrected and reexported + accurate parent.dat 2. Griffin bomb texture was implemented (it was forgotten in v1.0) and reexported
You can download v1.1 here :
Information : in v1.2, texture numbers will change, to match ITO architecture (vAicon will jump of joy, I bet)
Cheers,
Radium
I actually jumped a bit
-
@Radium and all the ones which actually helped to deliver this piece of art, thank you!
-
@antares190 Hello, thank you !
By respect for those who help me, I always keep an updated list of helping people.
https://forum.falcon-bms.com/post/349515
Cheers !
Radium