Hornet Ramp start Video
-
Every time you start bug I will squash one on the ground!
To be fair, tried carried take off TRN in F18D and except creepy RIO at back seat I was so impressed with feel for cat shots and traps and with F18D cockpit, with carrier ops and carrier model. Jeeez guys its that so good that it even deserves itās own avionics.
at least wikileaks were kind enogh to give use the entire IAM display logic for the Bug
Mush! -
Hereās one newer ā¦. forgive the imperfections. Itās good enough to get a ready to fly Hornet.
A little better resolution too.
nice work mate. never tested the e model that much to be honest.
-
Thatās not an E modelā¦you can tell by it having a UFC vice a UFCD.
-
Thatās not an E modelā¦you can tell by it having a UFC vice a UFCD.
Tell the modeler/skinner ā¦.
-
As Iāve pointed out elsewhere, itās F-16 BMS and not Hornet BMSā¦and Iām partial to the older Hornets as it is.
-
Thanks for this Agave. This will help me out a lot.
-
Hereās one newer ā¦. forgive the imperfections. Itās good enough to get a ready to fly Hornet.
A little better resolution too.
Agave,
For the falcon we have the idle cutoff handle which we click to move it to idleā¦ā¦when you mention the āidle detentā in the hornet are you referring to a toggle switch near or on the throttle? My throttles work fine during flight, but during a ramp start they are stuck in the fuel cutoff position. Is there something I am missing?
Burner
EDIT: Disregardā¦
I set my throttle to 50%, the used the Idle Detent keyboard function āALT - Iā, then retard throttle to idle and the
throttles are now responding. Thanks to Smokey at the 72nd VFW.1. -Wake up the throttle prior to doing anything-slide it full forward and back to the idle position (youāll notice the throttle in the 3dpit start moving)
-JFS
-RPM reaches 20-24% and SEC light turns off in the Caution Panel
-Throttle to approximately 50%
-Idle Detent (ALT-I)
-Slide throttle back to Idle2. Alternatively, you can use this if you have an idle detent on a Warthog HOTAS setup.
g_bUseAnalogIdleCutoff This option when enabled suppresses the need for the idle detent callback. The detent is simulated by the course of the throttle axis. The idle point must be declared with a right click on the SET AB button in the SETUP > CONTROLLER page of the UI. Enable this option if you have a strong physical detent at the idle point of your throttle. Available options: 0/1 ā default is 0.
-
Sure thing, I always like deals with you
seems to me you are lagging on me on that one already
-
Agave,
For the falcon we have the idle cutoff handle which we click to move it to idleā¦ā¦when you mention the āidle detentā in the hornet are you referring to a toggle switch near or on the throttle? My throttles work fine during flight, but during a ramp start they are stuck in the fuel cutoff position. Is there something I am missing?
Burner
EDIT: Disregardā¦
I set my throttle to 50%, the used the Idle Detent keyboard function āALT - Iā, then retard throttle to idle and the
throttles are now responding. Thanks to Smokey at the 72nd VFW. ā¦.Updated the video with some clarifications ā¦. including mentioning the ALT-I for throttle detent.
-
Is anyone else having issues with the 4.33 Hornet N1 RPM indicator.
If I load the default viper profile it loads properly, but as soon as I load my profile, the N1 indicator shows ā00ā the entire time. Is this a known error or is it something to do with my DTE settings?
-
Is anyone else having issues with the 4.33 Hornet N1 RPM indicator.
If I load the default viper profile it loads properly, but as soon as I load my profile, the N1 indicator shows ā00ā the entire time. Is this a known error or is it something to do with my DTE settings?
If youāre describing what I think you are, there is discussion on it. You can try with Smart Scaling of and/or with Shadows off as those were suggested āwork aroundsā that seemed to work for some.
-
If youāre describing what I think you are, there is discussion on it. You can try with Smart Scaling of and/or with Shadows off as those were suggested āwork aroundsā that seemed to work for some.
7-8 hours of diagnosing = frustrating
4 uninstalls and re-installs/20 profiles later = infuriating
Agave_Blue, a knowledgeable BMS dude = priceless.Thanks man, it was smart scaling all along. Too bad because I really like smart scaling which replicates real vision view distances. I disabled cockpit and focus shadows and the issue remained. Any ideas on what specific shadow to disable?
-
7-8 hours of diagnosing = frustrating
4 uninstalls and re-installs/20 profiles later = infuriating
Agave_Blue, a knowledgeable BMS dude = priceless.Thanks man, it was smart scaling all along. Too bad because I really like smart scaling which replicates real vision view distances. I disabled cockpit and focus shadows and the issue remained. Any ideas on what specific shadow to disable?
https://www.benchmarksims.org/forum/showthread.php?23650-F18-bug-BMS-4-33&highlight=smart+scaling
-
Thanks for the tut Agave!