Hornet Ramp start Video
-
That’s not an E model…you can tell by it having a UFC vice a UFCD.
-
That’s not an E model…you can tell by it having a UFC vice a UFCD.
Tell the modeler/skinner ….
-
As I’ve pointed out elsewhere, it’s F-16 BMS and not Hornet BMS…and I’m partial to the older Hornets as it is.
-
Thanks for this Agave. This will help me out a lot.
-
Here’s one newer …. forgive the imperfections. It’s good enough to get a ready to fly Hornet.
A little better resolution too.
Agave,
For the falcon we have the idle cutoff handle which we click to move it to idle……when you mention the “idle detent” in the hornet are you referring to a toggle switch near or on the throttle? My throttles work fine during flight, but during a ramp start they are stuck in the fuel cutoff position. Is there something I am missing?
Burner
EDIT: Disregard…
I set my throttle to 50%, the used the Idle Detent keyboard function “ALT - I”, then retard throttle to idle and the
throttles are now responding. Thanks to Smokey at the 72nd VFW.1. -Wake up the throttle prior to doing anything-slide it full forward and back to the idle position (you’ll notice the throttle in the 3dpit start moving)
-JFS
-RPM reaches 20-24% and SEC light turns off in the Caution Panel
-Throttle to approximately 50%
-Idle Detent (ALT-I)
-Slide throttle back to Idle2. Alternatively, you can use this if you have an idle detent on a Warthog HOTAS setup.
g_bUseAnalogIdleCutoff This option when enabled suppresses the need for the idle detent callback. The detent is simulated by the course of the throttle axis. The idle point must be declared with a right click on the SET AB button in the SETUP > CONTROLLER page of the UI. Enable this option if you have a strong physical detent at the idle point of your throttle. Available options: 0/1 – default is 0.
-
Sure thing, I always like deals with you
seems to me you are lagging on me on that one already
-
Agave,
For the falcon we have the idle cutoff handle which we click to move it to idle……when you mention the “idle detent” in the hornet are you referring to a toggle switch near or on the throttle? My throttles work fine during flight, but during a ramp start they are stuck in the fuel cutoff position. Is there something I am missing?
Burner
EDIT: Disregard…
I set my throttle to 50%, the used the Idle Detent keyboard function “ALT - I”, then retard throttle to idle and the
throttles are now responding. Thanks to Smokey at the 72nd VFW. ….Updated the video with some clarifications …. including mentioning the ALT-I for throttle detent.
-
Is anyone else having issues with the 4.33 Hornet N1 RPM indicator.
If I load the default viper profile it loads properly, but as soon as I load my profile, the N1 indicator shows “00” the entire time. Is this a known error or is it something to do with my DTE settings?
-
Is anyone else having issues with the 4.33 Hornet N1 RPM indicator.
If I load the default viper profile it loads properly, but as soon as I load my profile, the N1 indicator shows “00” the entire time. Is this a known error or is it something to do with my DTE settings?
If you’re describing what I think you are, there is discussion on it. You can try with Smart Scaling of and/or with Shadows off as those were suggested ‘work arounds’ that seemed to work for some.
-
If you’re describing what I think you are, there is discussion on it. You can try with Smart Scaling of and/or with Shadows off as those were suggested ‘work arounds’ that seemed to work for some.
7-8 hours of diagnosing = frustrating
4 uninstalls and re-installs/20 profiles later = infuriating
Agave_Blue, a knowledgeable BMS dude = priceless.Thanks man, it was smart scaling all along. Too bad because I really like smart scaling which replicates real vision view distances. I disabled cockpit and focus shadows and the issue remained. Any ideas on what specific shadow to disable?
-
7-8 hours of diagnosing = frustrating
4 uninstalls and re-installs/20 profiles later = infuriating
Agave_Blue, a knowledgeable BMS dude = priceless.Thanks man, it was smart scaling all along. Too bad because I really like smart scaling which replicates real vision view distances. I disabled cockpit and focus shadows and the issue remained. Any ideas on what specific shadow to disable?
https://www.benchmarksims.org/forum/showthread.php?23650-F18-bug-BMS-4-33&highlight=smart+scaling
-
Thanks for the tut Agave!