Ice’s Falcon BMS Profile Updated for BMS 4.37
-
Thanks. I Will try both ways. :lever:
-
If you have windows 10 and a supported wifi adapter there is a hotspot option you can enable and connect your mobile devices directly to windows 10 wifi adapter.
You can improve the latency by at least 200% and it’s nearly as good as tethered connection.
Also I set the option for 60fps in space desk.
Hi gr_chris_pilot, Your solution seems good to me, but I quite don’t figure out how to do it. I have an USB WIFI adapter available here. I understand that the process is:
1 - connect the Wifi USB adapter to the Desktop
2 - create a hotspot within windows 10 ( This is where I am a little lost here, mobile hotspot option perhaps?)
3 - connect the tablets wifi to this hotspot and NOT to my home wifi.
4 - Run Helios ControlIs that correct?
Cheers :yo:
-
Hi gr_chris_pilot, Your solution seems good to me, but I quite don’t figure out how to do it. I have an USB WIFI adapter available here. I understand that the process is:
1 - connect the Wifi USB adapter to the Desktop
2 - create a hotspot within windows 10 ( This is where I am a little lost here, mobile hotspot option perhaps?)
3 - connect the tablets wifi to this hotspot and NOT to my home wifi.
4 - Run Helios ControlIs that correct?
Cheers :yo:
This is exactly what I do!
The pc is gonna share its antenna in order to provide internet to the tablet as well. This is not gonna affect your pc internet speed.
It’s faster that way because there is no router relay lag in between.For me it works really nice!
-
Thanks, I will try that :yo:
-
Just a suggestion… Any thoughts of replacing the Roll & Trim indicators with A & B Hydraulic system gauges?? I make this suggestion because when coming off a target (especially when fired upon) I have Hydraulic gauges in my systems cross check. Putting them “up-front” would just make this cross check easier, plus there’s already a Pitch/Trim indicator on the combined console that I can reference and use to reset trim.
Just my 2-cents.
Cheers,
Jolly -
Just a suggestion… Any thoughts of replacing the Roll & Trim indicators with A & B Hydraulic system gauges?? I make this suggestion because when coming off a target (especially when fired upon) I have Hydraulic gauges in my systems cross check. Putting them “up-front” would just make this cross check easier, plus there’s already a Pitch/Trim indicator on the combined console that I can reference and use to reset trim.
Just my 2-cents.
Cheers,
JollyFor such a change maybe worth to get yourself into using the profile Editor as with some basic knowledge you could adapt such a change within a few minutes
Gesendet von meinem SM-G930F mit Tapatalk
-
For such a change maybe worth to get yourself into using the profile Editor as with some basic knowledge you could adapt such a change within a few minutes
Gesendet von meinem SM-G930F mit Tapatalk
Was somewhat hoping someone would suggest this. The one major limitation is there is no hydraulic gauges among the included images and I’m not very proficient at creating them from scratch. :tsk: But thanks for the reply Oak’. :thumb:
Cheers
-
Helios 1.6 has hydraulic gauges for the viper under F16 gauges in the controls editor. So it’s just a matter of putting them in place and assigning the Falcon bindings
Sent from my iPhone using Tapatalk
-
Hi Oakdesign, tnx for your answer. I‘ll give it a try.
Gesendet von iPhone mit Tapatalk
So far so good. Disabling the mouse-in-cockpit seems to remedy the problem. I keep my fingers crossed. Tnx, Oakdesign
Gesendet von iPhone mit Tapatalk
-
Helios 1.6 has hydraulic gauges for the viper under F16 gauges in the controls editor. So it’s just a matter of putting them in place and assigning the Falcon bindings
Sent from my iPhone using Tapatalk
Thanks Wheelchock…I didn’t see them when I looked earlier, but your reply just says I need to look harder. :nerd:
Cheers
-
I have a very customized key file and do not use touch screens but rather physical switches in my pit, including at the CPD.
Do I have to use Ice’s key file, which means a lot of reprogramming of hardware or can I use my custom key file by perhaps renaming in to “BMS - Ice’s Helios Profile”?
I do not use Alt Launcher.TIA
-
You could with Helios in the BMS interface you can reference a key file. You just need to ensure that all callbacks used by the Helios Profile are in your key file.
For functions such as the buttons on the CPD they are not handled by the keyfile as this are Helios internal touch functions. But you could assign DX Inputs on those Helios Touch buttonsGesendet von meinem SM-G930F mit Tapatalk
-
thank you sir.
-
Ice’s Falcon BMS Profile Updated to 4.35-8
Updated 25 May 2021:
The first post has been updated with the latest version.
Also added a CPD Only version for those that want to use the CPD without loading the full profile.
-
Ice’s Falcon BMS Profile Updated to 4.35-8
Updated 25 May 2021:
The first post has been updated with the latest version.
Also added a CPD Only version for those that want to use the CPD without loading the full profile.Thanks Linknet! Works great! That’s actually what I want, don’t need the button panel. Now I just need to use that combined with the gauges i’m currently using! Is there a Vietnam Map somewhere that will work in Helios?
-
Ice’s Falcon BMS Profile Updated to 4.35-8
Updated 25 May 2021:
The first post has been updated with the latest version.
Also added a CPD Only version for those that want to use the CPD without loading the full profile.
:whoo:
-
I’m installing the full profile (not the CPD one), but I’m being told there’s an image missing and the reference is to CPD images (see attachment) though the image is in the standard images folder. If I add the CPD folder the issue goes away.
Helios\Images\FalconBMS CPD Images 4.35\Buttons\CPD Reset.png
Helios\Images\FalconBMS Images 4.35\CPD\Buttons\CPD Reset.pngTANX
Critical
-
I’m installing the full profile (not the CPD one), but I’m being told there’s an image missing and the reference is to CPD images (see attachment) though the image is in the standard images folder. If I add the CPD folder the issue goes away.
Helios\Images\FalconBMS CPD Images 4.35\Buttons\CPD Reset.png
Helios\Images\FalconBMS Images 4.35\CPD\Buttons\CPD Reset.pngThanks for the information. I’d managed to cross reference the images between the Full and the CPD versions.
The first post has now been updated with the corrected Full 4.35-8 version.
For those that have already downloaded it just replace the “Ice’s Falcon BMS 4.35.hpf” profile file from the corrected version.
-
Great work and thanks for the support!
A couple of rookie questions that I can’t find an easy answer for:
1. Is there a button somewhere in the panels for the TrackIR reset (F12) hotkey?
2. What is the functional difference between the IFF PANEL vs AUX COMM button toggle? -
1. Would be that hard to add your own TrackIR reset button
2. Depending on which Block you fly you have differences in the Left side panel the button is to show hide either the IFF panel or the AUX Panel.Gesendet von meinem SM-G930F mit Tapatalk