A-a targets

[eagle-15]

i cant see the targets in a-a mode
and the stick botton ( fire gun no.1 ) didnt work

[LorikEolmin]

@eagle-15:

i cant see the targets in a-a mode
and the stick botton ( fire gun no.1 ) didnt work

It sounds a bit like “my car didn’t start this morning”. Could you tell us more?

[Agave_Blue]

@LorikEolmin:

…. “my car didn’t start this morning”. …

Did you check the battery? Did you have gas?

I’m guessing fuel pump issue. I recommend replacing it.

[eagle-15]

heheh
ur really funny 2guys
i turn into a-a mode …. i see some air craft in my ( ALR-56 RWR ) i try to find those aircraft in my radar but i cant … incrasing decreasing range … up and down … no thing …
at the same time my i cant use my gun ( pressing botton 1 ) even i set it in the controller page …
plsss help
by the way , i check battery … gas … even the tire …

[eclipsejpw]

did you try adjusting the antenna elevation? If you don’t have that set to the right block you won’t see anything.

As far as your Gun for A/A…did you have it in dogfight mode? otherwise you would have to cycle your a/a sms to the gun. Do you have proper gun symbology? Does your SMS say gun RDY?

[cptmtge]

did you ask awacs?

[Dee-Jay]

Master Arm?

[LorikEolmin]

Would they be choppers ?

[Dee-Jay]

Radar emitting (OVRD)?

[Jetlag]

Maybe try switching on ‘Labels’ to get better visuals on where targets are so that you can point aircraft (and therefore radar) at them. Wise advice so far about checking Master Arm etc

[VpR]

If they’re choppers, try GMT Radar mode.

[eagle-15]

eclipsejpw
my antina elevater hand up … i cant make it down or center
yes it work when i make it in dogfihgt mode … and also in a-g mode when i turn it to the gun … is it difrent with bms 4.32
Dee-Jay
yes master arm on
Radar emitting (OVRD) … what is this ?

[Dee-Jay]

@eagle-15:

Radar emitting (OVRD) … what is this ?

TO-BMS1F-16CM-1.pdf page 91 to 98

…

And RF switch position?

[Badger]

Just a long shot but, have you tried reading any of the manuals in your /docs folder ??

[eclipsejpw]

depending on the altitude of the target your trying to lock, you may have to change your antenna elevation.

[eagle-15]

i try to change antina elevation … but its hanging up i cant changing it down or at the center …. its move alittle bit … and flashing a lil …

[eagle-15]

Jetlag
how can i switch on “labels”

[cptmtge]

shift-l for near labels and ctrl-l for far labels and enable them in settings screen

[Jetlag]

@eagle-15:

i try to change antina elevation … but its hanging up i cant changing it down or at the center …. its move alittle bit … and flashing a lil …

Hello Eagle 15
maybe share with us all what is joystick gear you have? Thrustmaster? Cougar? Warthog? CH? Saitek?

[macieksoft]

If you have antenna elevation full up targets will not show.
Just assign one of joystick knobs (if your joy have any) to the radar antenna elevation, its usually the best way to go. You can do it with Cougar, Warthog (yes, AFAIK it have one free axis) and X52 (it have as much as 2 knobs and one slider). I am using this little knob on my X52 PRO for this function while the big knob is for sniper pod zoom.