Thanks Amedeus.
I reattached the image. I launched the x56 software and it recognizes both RTY 3 and TRY4
Thanks Amedeus.
I reattached the image. I launched the x56 software and it recognizes both RTY 3 and TRY4
Thanks Amadeus,
I normally have RTY 3 mapped to my altimeter and 4 to the Range Knob, but for some reason I only see one RTY dial as an option in the dropdown menu. I moved it from ALT to Range. Any idea where the other RTY option might be?
HI all,
I don’t use any DX mapping, and just assign each button in the controller section of BMS.
I used to have RTY4 mapped to the TGP page so I could zoom in to 4.0X, but that somehow got dropped… Any suggestion oh how to re-map it?
Thx!
bruzzer
Thanks jayb… I’ll give that a try.
Hi guys,
I’d like to remove some button assignments (clear t out) on my Saiteck X-56. but I think it’s something I need to do in the controls section of BMS. Any tips or do I start over from scratch?
Thanks
Been thinking about trackIR ,… what do you like about it?
Has anyone done anything with the stick that is on the side of the joystick (not the throttle - I use that for radar cursor control). In theory I would like it to change views so I can map the trim button correctly.
Thanks
Man I hope this what’s been going on with my AP… I love this forum
Hey there guys,
Is anyone able to use their ministick on the actual joystick? I’ve dedicated one toggle (the silver one) for viewing around, as I don’t have track IR. I was hoping to change the viewing to the ministick.
Also, in case any of you are experts… I was able to assign RTY 4 to comtrol my altimeter, but can find no recognition in the game for RTY 3 or for the F and G rotary knobs.
Hey Klog, I was in your same boat a few days ago.
These videos proved very useful
For training, (if you are not familiar), use the BMS training manual in the docs folder and pair the up with these videos
I downloaded the file and installed with no problems, but when I launch 4.34 i still only have the original Korea campaign
Hi ddoc,
So I reset the throttle CAL, and I see the Mx (min thrust) and the Mn (max thrust) flags. I’m not sure I follow in regards to “keep an eye on them.” They seem to be fairly static in range when I reset their location.
I actually wan to say the first time I ran HID I did see full throttle movement.
I then set Idle and Aft again. Unfortunately the biggest part of the throttle line is still dark green.
Also including a pic of how Windows is seeing my TUSBA in the hardware section in case that makes any difference.
Cheers
Thanks Stevie, let us know if you manage to solve it.
ddoc,
EDIT: I WAS ABLE TO FLASH THE TUSBA. when I try and flash the TUSBA, it appears grey in the software. If I unplug it and plug it back in, it flashed black (ready to be updated) and then grey after a second (as if not detected), and won’t let me flash the TUSBA. Any idea?
With that done, I’m going back into BMS now to see what happens.
EDIT: Unfortunately not good news. The X/Y cursors wander and I get no response from the throttle, even though in the settings it shows some (very limited) motion. Basically full throw of the throttle only amounts to 1/4 of the blue bar filling up. In game I get no response from the throttle at all.
Cheers ddoc. Hoping the pictures help.
Hi ddoc,
I unplugged my TUSBA then restarted my computer, plugged it back in and DCC confirms that the firmware is 1.07. Below are the screen shots of my DCC both at idle and full AB, with a comparison shot of yours.
I will log into BMS now and verify the axis assignments. I did some google searching to see if it’s possible to verify potentiometers and their output but didn’t find anything (except taking it apart and using lab equipment). I did notice that you had the axis mapped to your RUSBA. Pretty cool!
Also, can you select targets with your radar cursor enable click? I remember being able to do that…
Is there a way to verify my Vipergear HALs are working properly, and that I’m getting the correct deflection out of them?
Thanks