4.33 Issues (Known or not)
-
I post my video again about the known issue of the “Harrier-Shaking bug”.
-
it happens to me too… it even managed to flip once…i thought it was from rough landing…
-
I have not used the Harrier yet, but interesting to know that there might be a bug associated with that. I believe many issues are being addressed as I speak. But for now, we need to AGAIN, be patient with any new issues this new version has. The devs have been hard at work to give us a new sim with extraordinary features. There are bound to be issues. For now, I would say work around it and give the devs some much needed down time. Being patient thus far has proven good works come from it.
-
Harrier shaking bug is a bug known before release
it happens on weak systems where FPS are low on airbases…
this will be fixed in U1 , the tricky part is that i can not reproduce it on my rig since i can not run 4.33 below 40 fps…
-
Harrier shaking bug is a bug known before release
it happens on weak systems where FPS are low on airbases…
this will be fixed in U1 , the tricky part is that i can not reproduce it on my rig since i can not run 4.33 below 40 fps…
Thanks Mav,
Any info regarding changing the 2D pit FOV?
-
I’d like to throw in a possible texture bug. SA-2, SA-3, and SA-5 have no skins. They are just gray models. The SA-4 has a “skin” but looks like it was misapplied.
-
I’d like to throw in a possible texture bug. SA-2, SA-3, and SA-5 have no skins. They are just gray models.
Not a bug. (model don’t have textures (yet))
-
I have communication menu issue. When I call tower by typing “T”. Sometimes, number of command 2,3 are overlapped, or a command is not fully displayed.
How can I explain that? The bottom command line is half disappeared? When I chose command 2 request. I say abort landing.
I though the command has sub commands like refuling. reloading something like that. But abort landing! -
I have communication menu issue. When I call tower by typing “T”. Sometimes, number of command 2,3 are overlapped, or a command is not fully displayed.
Comms box size issue relative to your resolution. We are working on that problem (was the same in 432)
-
I have communication menu issue. When I call tower by typing “T”. Sometimes, number of command 2,3 are overlapped, or a command is not fully displayed.
How can I explain that? The bottom command line is half disappeared? When I chose command 2 request. I say abort landing.
I though the command has sub commands like refuling. reloading something like that. But abort landing!Hi there mate.
Well if you mean exactly the below situation:
Then you have probably the dpi resolution at your monitor above 100%.
Try to lower that setting (or set it 100%) and you will fix it ;).
Nikos. -
Hi there mate.
Well if you mean exactly the below situation:Then you have probably the dpi resolution at your monitor above 100%.
Try to lower that setting (or set it 100%) and you will fix it ;).
Nikos.Hi! Yes, exactly. I think you have a right solution to fix this. However, I didn’t have this problem with 4.32 version.
I think I should wait until next patch as Dee-Jay mentioned. or have to follow your way until the patch is released.
Thanks! -
Hi! Yes, exactly. I think you have a right solution to fix this. However, I didn’t have this problem with 4.32 version.
I think I should wait until next patch as Dee-Jay mentioned. or have to follow your way until the patch is released.
Thanks!That is correct. I also had no that specific issue in BMS 4.32, but now i have ;).
Since Dee-Jay said that will gonna be fixed, it will.
Until then, just keep it in mind as a temporary solution, it is confirmed by me.
Nikos. -
1. what happened to the old keystrokes; the expanded ones are different and now I am unable to figure out how to lock the target with keyboard (num lock) cursors in HAD and radar modes please advise asap.
It also appears that saved settings revert back to defaults including labels, weapons effects and messages for example. -
1. what happened to the old keystrokes; the expanded ones are different and now I am unable to figure out how to lock the target with keyboard (num lock) cursors in HAD and radar modes please advise asap.
It also appears that saved settings revert back to defaults including labels, weapons effects and messages for example.RTFM and learn to use TMS
-
Not sure if this is covered in the manual, only read ca 70 pages yet, I noticed in the UI (mission and missions schedule) the “show names” feature is not available in my install and ancient rig.
Not a big deal though. -
Since Dee-Jay said that will gonna be fixed, it will.
Dee-Jay didn’t said that it will be fixed, he said that DEV are working the problem. Maybe not to be expected for the next patch.
-
This post is deleted! -
I don’t know what is the problem, but I can’t control the view in the game via mouse or keyboard.
I tried both version 32 and 64 bit but the problem is same.
I use default full key set .And no connected joystick or other periferia on the PC except keyboard+mouse.In the advanced control menu It is work but in game not. I tried shift+4,6,2,8, and right mouse button to look around in the cockpit, but it isn’t work.
But I can use the scroll button to lean left or right
I have no joystick now, becouse it is in serviceI would like to learn the game until , but I can’t now.
PC spec:
AMD 965x4
HD4850 1gb
8gb RAM
Asrock 970ext4
USB laser mouse -
I assume you think that’s a helpful response yet frankly if you can’t help please don’t tell me to RTFM. @Mav-jp:
RTFM and learn to use TMS
-
1. what happened to the old keystrokes; the expanded ones are different and now I am unable to figure out how to lock the target with keyboard (num lock) cursors in HAD and radar modes please advise asap.
It also appears that saved settings revert back to defaults including labels, weapons effects and messages for example.Hey m8!
I understand that its confusing but the only option is to read the manuals and reconfigure the hotas with the new keyfiles.
U will find everything you had before in there its just another keystroke assigned to that callback.Clear skies!