YAME64 suite
-
@Red:
But to narrow your issue, it would be most useful to know what callback you’re trying to emulate exactly
I’m using Helios to send keystrokes to YAME to control the “Center pedestal block 60” and select it’s various buttons. These are not the callbacks from YAME to BMS which are all working except for the CP60_OSB20 “Mode” button which sends the correct callback to BMS but only responds to every second tap on the touchscreen.
So in the YAME callbacks section if I set keyboard keys for the CP60_OSB20 and CP60_OSB24 callbacks the CP_60 buttons do not respond to the keystrokes either from Helios or from direct keyboard entry.
-
not familiar with Helios. And your setup seems pretty complicated with a lot of source for errors
and you still didn’t tell me specifically WHICH callback you’re trying to emulate?what function are you trying to program into these 2 OSB?
-
@Red:
not familiar with Helios. And your setup seems pretty complicated with a lot of source for errors
and you still didn’t tell me specifically WHICH callback you’re trying to emulate?what function are you trying to program into these 2 OSB?
I’m not trying to program any function to send to BMS into these 2 OSB’s. Forget about BMS :). I’m merely trying to control the YAME “Center pedestal block 60” display via keyboard buttons from Helios. For instance sending a keystroke to OSB24 only changes the YAME “Center pedestal block 60” MFD’s from left to right, it doesn’t make any changes or send any callbacks to BMS.
-
Hi Tweety,
just some ideas:- I checked the YAME config files and i could not find any entry looking like an IP address, so I think it gets the address on the fly.
- please check your IP adress again on the command line: cmd -> ipconfig
there should be an entry like: IPv4 Address……192.168.178.21
If there is no IPv4 Address then that might be your problem. I can imagine YAME is not IP6 ready.
And finally: start YAME with admin permissions, at least it would not work correctly on my system without admin permissions.
Hello Kisakuru,
I also checked all YAME files in the “conf” folder with no luck.
I checked my IP address with ipconfig and it shows up well (192.168.2.1).
I always start YAME with Admin rights (even if not required on my SimPit).
I installed YAME on my other PC (including BMS4.33, ++) and there it shows the IP adress 192.168.178.21 by default (even when I set the IPv4 to 192.168.2.2). I disabled all Firewall, AV and so on. Both PC see each other in peer to peer. Any other ideas?
P.S.: My SimPit PC is Win7 and the “Client” PC is Win10. Might that be a problem?
Thanks again for any help.
Have a great evening,
Tweety -
Is the server problem or the client?
-
Is the server problem or the client?
Hello Roccio,
Its looks like a Server Problem, it shows only 0.0.0.0 for the local IP adresse.
Greetz, Tweety -
Hello Roccio,
Its looks like a Server Problem, it shows only 0.0.0.0 for the local IP adresse.
Greetz, TweetyIs the server pc connected to the internet?
-
Is the server pc connected to the internet?
No, I try a peer-to-peer connection to my second PC.
But this is one if the next steps (via the router)
If you want or have more information we can go via PM.
Thanks for your help,
Tweety -
Mmm that could be the problem. If the pc is not connected to the Internet the network library used should fail to get the ip address and ence working
-
Mmm that could be the problem. If the pc is not connected to the Internet the network library used should fail to get the ip address and ence working
That might be the reason why it worked on my Laptop, as it was connected to the WLAN.
Many thanks for the hint.
I gonna try it (hopefully) tomorrow.
Thanks and have a great evening,
Tweety -
Mmm that could be the problem. If the pc is not connected to the Internet the network library used should fail to get the ip address and ence working
Hi Roccio,
Many thanks, it works
:bdance:
No I have to configurate the new screens. My Album will be udpated soon
Thanks again and have a great evening,
Tweety -
Hi folks,
trying YAME2 with BMS 4.35, the gauges work but the MFDEs look kind of weird (the MFDE Server app on the android tablet picks them up correctly as you can see from the RWR / DED textures on the tablet).
Any idea what could be causing this? Thanks!
All the best,
Uwe
-
Mhh… all fine here with YAME & 4.35.
RTT Texture enabled in Config ? -
Yep, I had forgotten that at first but now my RWR and DED in the android app are back, the gauges work fine in YAME and it’s only the MFDs that are messed up.
Thanks for your help!
Uwe
-
My MFDs are corrupted also, RTT set to 1…
-
MFD’s and DED are messed up, they show something (just a bunch of lines) the rest work just fine
-
Hi folks,
trying YAME2 with BMS 4.35,
Hi Hoover,
Is YAME2 a typo for YAME64 or is there an updated YAME64 which would be great.
-
MFD’s and DED are messed up, they show something (just a bunch of lines) the rest work just fine
MFD, DED, RWR exrtractions in YAME are messed because they aren’t adjusted to the DX11 new in 4.35. All gauges that rely only on sharedmem data work fine. All items that rely on extracted textures won’t.
-
copy
-
Use RTT client for those or MFDE