awesome
Posts made by Windmill
-
RE: BMS 4.35.2 How to turn on the HMCS in my F-16 CM50
Thx guys for the suggestions. i’ve figured it out . i only had the encoder mapped and not the on of function. thx
Windmill
-
BMS 4.35.2 How to turn on the HMCS in my F-16 CM50
Fellow Viper simmers,
I updated my rig to 4.35.2 and am trying the enhanced SEAD experience. I always fly with the USAF Block 50. I have my hardware encoder mapped to [ and ] for the inc and decr of the JHMCS. But no effect…… trying to turn it on by mouse click (or scroll) has no effect. I did notice that if I start the Viper on the RW (I normally use the ramp) it is already turned on.
I am clueless. any suggestions?
Windmill
-
RE: Trying to get my cougat hotas recognised by my W10 PC
The manual says put it to auto cakibration, put it to manual calibration.
I know i need to update the manual but i simpley to busy to get the new icp done.Redneck,
I just send you an email (sales@……)
Windmill
-
RE: Trying to get my cougat hotas recognised by my W10 PC
I keep getting this error message:
-
RE: Trying to get my cougat hotas recognised by my W10 PC
Good to know you got it sorted.
Any idea what did the trick?I think the TUSBA was preventing detection. After I disconnected and did everything again it started to go uphill from there. The only thing now is that if I put my values (using CCP) at 320-330) I get good response for the roll. But not for the Pitch control. I can pull stick but I cannot bring the nose down.
any suggestions?
-
RE: Trying to get my cougat hotas recognised by my W10 PC
Redneck, Badger,
after fiddling around I was able to try everything over again. and I was able to connect to CCP. So I managed to finish with the VIPERGEAR manual. So, I think I m good now.
cheers
-
RE: Trying to get my cougat hotas recognised by my W10 PC
Badger and Redneck,
I first removed all my cougar listings as suggested by redneck. After that I installed using Badger’s link. I selected the windows 8 compatibility mode in the properties.
But to no avail. I keep getting the E2 failure after starting the CCP. I also followed the troubleshoot page. But it keeps saying the cougar is connected. (In USBdeview it shows as connected)
Verzonden vanaf mijn iPad met Tapatalk
-
Trying to get my cougat hotas recognised by my W10 PC
Hey Viper drivers,
I always used my cougar stick directly via the windows control panel. It always worked fine but I tried to start using HOTAS CCP and FOXY. the documents said to hold the trigger while plugging in the joystick. The result is that the CCP does not detect my cougar and that the regular w10 control panel does recognise the device but there are no axis anymore. The final result is that CCP does not work but I also cannot calibrate my stick anymore.
Is it possible to reinstall firmware?
BTW I run the throttle through TUSBA and I just installed VIPERGEAR VFS
Any of you guys a clu?
Cheers,
Windmill
-
RE: [Released] EMF v1.0.3a (BMS 4.34)
Good Morning Viper drivers,
I am using BMS 3.34. I noticed that this theater in the 1.02 version had two campaigns. now that I upgraded to 1.03a the campaigns are not available anymore. Is there any indication when there will be campaigns available in the 1.03a version?
cheers,
Windill
-
RE: POH 0.8.1 for BMS 4.34 - Bug Tracker
super, I think it did the trick.
Cheers,Windmill
-
RE: POH 0.8.1 for BMS 4.34 - Bug Tracker
Dear Nuno,
My Iberia campaign gives a save error.
It saves all right but somehow if I open de saved menu and try to load, the map shows of empty. E.g. I cannot select any unit. Therefor it will not load.
-
RE: Mission commander does not load mission
both Korean Theatre and Balkans
-
RE: Mission commander does not load mission
Thanks for the reply. I tried but to no avail.
BTW I noticed my WDP gives a similar error message.
cheers,
Remco
-
Mission commander does not load mission
Hi all,
I recently upgraded to 4.34. It runs smoothly on my system. I also upgraded MSC to its latest version. If I run MSC it starts fine. However, if I try to load a mission (so I can change alter it) it gives an error message. It tells me that it is unable to load because the lzssNative.dll is missing.
But if I check the MSC folder, the lzssNative.dll is in it……
any suggestions?
Windmill
-
Possibility to shorten the ramp time?
Dear Viper drivers,
All the best for 2019.
I was wondering, is there a possibility to change the s(standard) time on the ramp? It is set on 20 minutes. Can it be changed to, lets say, 15 minutes? And, how do I do that………
CHeers,
Windmill